TechnSols
Advertisement

Hydraulic Pressure Calculator

Hydraulic Pressure Calculator free online: work out force, pressure and cylinder bore size from Pascal's law. No install, no sign-up.

Be the first to rate this tool

Enter the pressure and bore, then press Calculate Force.

What Is Hydraulic Pressure Calculator?

Hydraulic Pressure Calculator is a free online tool by TechnSols that works out the force a hydraulic cylinder delivers from its pressure and piston size, the pressure a job needs from its force and bore, and the bore size a cylinder needs for a required force at a given system pressure. It is Pascal’s law as a calculator: force equals pressure times area, with the piston area worked out from the bore diameter.

Advertisement

A cylinder that is too small for its load stalls, and one far too large wastes money, oil, and space. The size question comes up everywhere hydraulics are used: a press that must push with a known force, a lift that must raise a known weight, a clamp that must hold a workpiece, or a splitter that must drive a wedge through wood. The calculator turns the load and the system pressure into a bore size, or turns a bore and a pressure into the force on offer, before any cylinder is ordered. When the force must be stated in another unit, the Pressure Converter changes bar, megapascals, and psi between units.

Force mode takes pressure and bore and gives the push force, plus the pull force when a rod diameter is given. Pressure mode takes the required force and the bore and gives the pressure the system must reach. Bore mode takes the required force and the system pressure and gives the minimum bore diameter, which is then rounded up to the next standard size. When the load is given in tonnes or pounds first, the Unit Converter changes it into kilonewtons.

How To Use Hydraulic Pressure Calculator?

Using Hydraulic Pressure Calculator takes less than a minute, with no software to install and no account to make. Pick what to work out, type two numbers, and read the answer. The Volume Converter changes litres and cubic centimetres into the same unit.

Step 1: Pick What To Work Out

Choose one of the three modes. Force mode checks a cylinder you already have: give its pressure and bore and learn what it can push. Pressure mode checks a system: give the force and the bore and learn the pressure required. Bore mode sizes a new cylinder: give the force and the system pressure and learn the smallest bore that does the job.

Step 2: Enter The Pressure, Bore, And Force

Type the numbers the mode needs. Pressure can be given in bar, megapascals, or psi, and the tool converts between them. The bore is the piston diameter in millimetres, and the force is given in kilonewtons. In force mode, a rod diameter can be added too, which gives the retract force as well as the extend force. The Area Converter changes piston area into square centimetres or square inches.

Step 3: Read The Result And Download The Summary

Press the calculate button and read the piston area, the pressure, and the force in newtons, kilonewtons, and tonnes. In bore mode the answer is the minimum bore diameter, with a note to round up to the next standard bore size. Download the text summary with the Download button, and change any input for a new size: the old result clears at once.

The numbers can be used straight in a design note.

Why Does Bore Size Matter So Much?

Force grows with the square of the bore diameter, because the piston area is pi times the diameter squared over four. Doubling the bore does not double the force, it multiplies it by four, and going from a 50 millimetre bore to a 63 millimetre bore raises the force by about 59 percent at the same pressure. That square law is the single most useful fact in cylinder sizing: when more force is needed, a larger bore helps far more than a higher pressure, and higher pressure only stresses seals, hoses, and the pump. The Pascal’s Law page explains why pressure acts equally on the whole piston face.

Pressure has its own limits too. Most industrial systems run between 100 and 250 bar, and pushing beyond the relief setting only opens the relief valve and turns the extra energy into heat. A cylinder sized at the relief pressure will stall on a cold morning when the oil is thick, so design from the steady working pressure, not the relief setting.

What Is The Difference Between Extend And Retract Force?

On the extend stroke the push force is pressure times the full piston area. On the retract stroke the piston rod occupies part of that face, so the pressure acts only on the ring of area left around the rod, and the pull force is always lower. With a 50 millimetre bore and a 25 millimetre rod, the retract area is only three quarters of the bore area, so the pull force is three quarters of the push force.

How Much Safety Margin Should A Cylinder Have?

Real cylinders lose about 5 to 10 percent of their theoretical force to seal friction, and side loads and pressure drops in lines and valves take a little more. The usual practice is to size the cylinder for 80 percent of its theoretical force, or to apply a safety factor of 1.25 to 1.5 on the load. A cylinder rated exactly at the load will stall when conditions are worst. When the power the pump must deliver is part of the sizing, the Power Converter changes watts and horsepower between units.

Why Round Up To A Standard Bore Size?

Cylinders are made in standard bore sizes, such as 32, 40, 50, 63, 80, and 100 millimetres, and a calculated bore of 63.08 millimetres cannot be bought as a 63 millimetre cylinder, because that bore is slightly too small. The next size up, 80 millimetres, is the one to order, and its extra force becomes part of the safety margin.

What Can You Do With Hydraulic Pressure Calculator?

Hydraulic Pressure Calculator fits any job where a cylinder must push, pull, lift, or clamp with a known force. These are the jobs it handles best, from a workshop press to a machine clamp.

Size A Cylinder For A Press

A press that must push with 50 kilonewtons at 160 bar needs a bore of at least 63.08 millimetres, so the next standard bore of 80 millimetres is the right order. Enter the force and the pressure in bore mode and the calculator gives that minimum bore at once.

Check What An Existing Cylinder Can Push

A cylinder already on the machine can be checked in force mode: a 50 millimetre bore at 100 bar gives a piston area of 1963.5 square millimetres and a push force of 19635 newtons, which is 19.63 kilonewtons or about 2 tonnes. That number tells at once whether the cylinder can lift the load. The Temperature Converter changes oil temperature between Celsius and Fahrenheit.

Work Out The Pressure A Job Needs

When the cylinder is fixed and the load is known, pressure mode gives the pressure the system must reach. That number decides the relief valve setting and shows whether the pump can do the job at all. If it is above the system rating, the answer is a larger bore, not a higher relief setting.

Every hydraulic job needs the same three numbers, the pressure, the bore, and the force, and this tool gives any one of them from the other two. That is the whole job. When the cylinder drives a rotating part, the Bearing Calculator works out the bearing life for the load.

Advertisement

Quality And Settings

The quality of the answer depends on the inputs. The pressure must be gauge pressure, not absolute pressure. The bore must be the piston diameter, not the outside of the barrel. The force must be the real load, including the weight of the tooling. The Hydraulic Cylinder page shows how the bore, rod, and seals fit together inside a cylinder.

  • Use gauge pressure from the system gauge, not absolute pressure.
  • Measure the bore, the piston diameter, not the barrel outside.
  • Include the weight of tooling and fixtures in the load.
  • Size for 80 percent of theoretical force to cover seal friction.
  • Round the calculated bore up to the next standard size, never down.

When the inputs are honest, the answer is honest too: a theoretical force from Pascal’s law for steady pressure on a piston. Seal friction, side loading, and pressure drops all take a share in real machines, so the theoretical number is the ceiling, not the delivered force. The Density Converter changes oil density between units.

How Hydraulic Pressure Calculator Works

The calculator starts from Pascal’s law: pressure applied to a confined fluid acts equally in all directions, so the force on the piston is pressure times the piston area. The piston area is pi times the bore diameter squared over four, and one megapascal equals one newton per square millimetre, which makes the metric arithmetic simple. A 50 millimetre bore has an area of 1963.5 square millimetres, so at 10 megapascals, which is 100 bar, the force is 10 times 1963.5, which is 19635 newtons.

For the retract stroke the rod area is subtracted first: the effective area is pi over four times the bore squared minus the rod squared, and the pull force is pressure times that ring of area. For bore sizing the law is inverted: the required area is force divided by pressure, and the bore is the square root of four times that area over pi. Two honest limits apply: the force is theoretical, before seal friction, and the tool assumes steady pressure with no account for dynamic loads or rod buckling.

For the worked example, 100 bar on a 50 millimetre bore gives 19635 newtons, which is 19.63 kilonewtons or about 2 tonnes. A 50 kilonewton job at 160 bar needs a 63.08 millimetre bore, so the next standard bore of 80 millimetres is the order.

Privacy

Everything you calculate stays in your browser. Hydraulic Pressure Calculator runs on your own computer, and nothing you type is uploaded to a server, stored, or shared with anyone. The tool does its job and shows the answer, and that is all it does.

No account is needed, so no name, email, or history is tied to what you do. Closing the tab ends the session, and nothing about it is kept, shared, or sold.

Tips

A few habits make Hydraulic Pressure Calculator work smoother.

  • Size from the steady working pressure, not the relief valve setting.
  • Check the retract force separately when the job must pull.
  • Keep a 20 percent margin above the load for friction and cold starts.
  • Round the bore up to the next standard size, never down.
  • Download the summary before you clear the numbers.

When the bore is rounded up and the margin is kept, the cylinder does its job on the worst day, not just on the best one. The Energy Converter changes kilowatt hours into joules.

More Tools For The Same Job

These tools handle the same kinds of jobs.

  • Pipe flow: a pipe flow calculator works out velocity, head loss, and pressure drop in a pipe.
  • Pressure Converter: changes pressure between bar, kilopascals, psi, and megapascals.
  • Unit Converter: changes any measurement unit into another in seconds.
  • Area Converter: changes piston area between square millimetres and square inches.
  • Volume Converter: changes cylinder oil volume between litres and cubic centimetres.
  • Power Converter: changes pump and motor power between watts and horsepower.
  • Bearing Calculator: works out bearing life and load for rotating machine parts.
  • Density Converter: changes fluid density between kilograms per cubic metre and other units.
  • Temperature Converter: changes oil temperature between Celsius and Fahrenheit.
  • Energy Converter: changes work and energy between joules and kilowatt hours.

FAQ

Common questions about hydraulic pressure, answered plainly.

Is Hydraulic Pressure Calculator By TechnSols Free?

Yes, Hydraulic Pressure Calculator by TechnSols is completely free to use, with no account, no sign-up, and no usage limit. You can size as many cylinders as you like, and everything runs in your browser, so nothing is uploaded or stored anywhere.

What Is Pascal’s Law?

Pascal’s law says pressure applied to a confined fluid acts equally in all directions, so the force on a piston is pressure times the piston area. Double the pressure or double the area and the force doubles. It is the whole basis of hydraulic power, from a car jack to a press.

Why Is Retract Force Lower Than Extend Force?

On the retract stroke the piston rod takes up part of the piston face, so pressure acts only on the ring of area around the rod. That smaller effective area gives a smaller force at the same pressure, which is why a cylinder that pushes a load easily can still struggle to pull it back.

How Do I Choose A Bore Size?

Give the force the job needs and the pressure your system runs at, and the calculator gives the minimum bore. Round that number up to the next standard bore size, such as 32, 40, 50, 63, 80, or 100 millimetres, and keep a margin of about 20 percent for seal friction and cold starts.

Is The Calculated Force What The Cylinder Really Delivers?

No, the calculated force is theoretical. Seal friction takes about 5 to 10 percent, and side loads and pressure drops in lines take a little more. Size the cylinder for about 80 percent of its theoretical force, and the delivered force will cover the real load.

Enter the pressure and the bore, and read the force. A cylinder sized this way pushes its load with margin to spare, and that is the whole point of the check.

Follow TechnSols on Google
Add TechnSols as a preferred source to see more of our tools in Google Search.
Add to Preferred Sources
Advertisement