TechnSols
Advertisement

Thread Pitch Identifier

Thread Pitch Identifier: free online tool to name any metric or UNC/UNF thread from measured diameter and pitch. No install, no sign-up.

Be the first to rate this tool

Enter the measured major diameter and the pitch or threads per inch, then press Identify Thread.

What Is Thread Pitch Identifier?

Thread Pitch Identifier is a free online tool by TechnSols that names an unknown screw thread from two measurements: the major diameter and the thread pitch. Type the measured diameter in millimetres and the pitch in millimetres or in threads per inch, and the tool gives the closest standard threads, with ISO metric coarse and fine sizes and UNC and UNF inch sizes, plus a match quality for each one.

Advertisement

An unknown bolt is a common workshop problem. The nut is missing, the part number is worn off, or the bolt came from a machine with no manual. A bolt with the wrong pitch will not thread in, and forcing it ruins the tapped hole. The identifier compares the measurements with real standard tables, so the thread can be named before a replacement is ordered. When the diameter was measured in inches, the Length Converter changes it into millimetres first.

The tool also gives the tap drill size for metric threads and the pitch in both units for every match. Everything runs in your browser, and no file is uploaded anywhere. The result can be downloaded as a short text summary to keep with the job or send to a supplier.

How To Use Thread Pitch Identifier?

Using Thread Pitch Identifier takes less than a minute, with no software to install and no account to make. Measure the bolt, type the two numbers, and read the answer. When the numbers need changing between units first, the Unit Converter changes them in seconds.

Step 1: Measure The Major Diameter

Measure the outside of the thread with calipers, across the crests, and type the result in millimetres. This is the major diameter, and it is the number the M in a metric size refers to: an M10 bolt measures 10 millimetres across the crests. A real bolt measures a little under size, so 9.9 millimetres still points at M10. When threads per inch must be turned into a pitch in millimetres, the Scientific Calculator divides 25.4 by the TPI count.

Step 2: Measure The Pitch Or Count The Threads

Measure the pitch with a thread gauge, or count the threads over 10 millimetres and divide, or count the threads over one inch for TPI. Pick the input the measurement used: pitch in millimetres, or threads per inch. The pitch is the distance between two neighbouring crests, and it is what decides whether a nut fits. When threads are counted over a length instead of one pitch, the Ratio Calculator turns the count into a pitch.

Step 3: Read The Matches And Download The Summary

Press Identify Thread and read the closest standard threads, each with its match quality: exact, very close, or closest. Download the text summary with the Download button for a record, and change any input to try a new reading: the old result clears at once, so a stale answer is never shown.

The whole check is two measurements and one click, and the answer names the thread to order, the tap to use, or the nut to try.

Why Does Thread Pitch Matter?

Thread pitch is the distance between neighbouring threads, and it decides whether two parts fit together at all. Two bolts can share the same diameter and still be useless together: an M10 bolt with a 1.5 millimetre pitch will not thread into an M10 hole cut at 1.25 millimetres. The diameter alone never names a thread. The ISO Metric Thread page explains how metric threads are named by diameter and pitch, and why the coarse pitch may be left out of the name.

Pitch also decides how a joint behaves. A coarse thread assembles fast, resists dirt and damage, and suits soft material and general work. A fine thread of the same diameter is stronger in tension, resists vibration better, and suits thin walls and adjustment screws, but it cross threads more easily and is slower to tap. When a threaded pipe joint must hold pressure, the Pressure Converter changes the working pressure between bar and PSI.

What Happens With The Wrong Pitch?

A nut with the wrong pitch starts to turn, then jams after a turn or two, because the threads do not line up. Forcing it strips the threads in the nut, the bolt, or the tapped hole, and the repair is a larger hole, a thread insert, or a new part. A bolt that feels tight after one turn is almost always the wrong pitch, not a tight fit.

How Do Metric And Inch Threads Differ?

Metric threads are named by diameter and pitch in millimetres, such as M10 by 1.5, while inch threads are named by diameter and threads per inch, such as 3/8-16 UNC. The two systems are not interchangeable, even when the diameters look close: a 10 millimetre bolt is not a 3/8 inch bolt, and their pitches never match exactly. Measuring both numbers is the only way to tell them apart.

Why Do Real Bolts Measure Under Size?

A real bolt measures a little under its nominal diameter, because the standard allows the thread to sit slightly below the sharp crest. That is normal, and it is why the identifier shows very close matches as well as exact ones. A reading of 9.85 millimetres with a 1.5 millimetre pitch is still an M10 coarse thread, and the tool says so instead of reporting no match.

What Can You Do With Thread Pitch Identifier?

Thread Pitch Identifier fits any job where a thread must be named before a part is ordered or a hole is tapped. These are the jobs it handles best, from a home repair to a machine shop.

Replace A Bolt With No Part Number

A bolt from an old machine often has no readable marking, and the manual is long gone. Measure the diameter and the pitch, and the identifier names the standard size to order. The match also gives the tap drill size, so a damaged hole can be re-tapped to the same thread. When the bolt strength must be checked from its size, the Area Converter changes the thread stress area between square millimetres and square inches.

Tap A New Hole To Match A Bolt

A new bracket needs a tapped hole that takes an existing bolt. Identify the bolt thread first, then drill the tap drill size the tool gives and cut the thread with the matching tap. Get the thread right before drilling: a hole drilled for the wrong tap cannot be made smaller. When the hole depth and drill volume must be worked out, the Volume Converter changes the hole volume between cubic millimetres and cubic centimetres.

Sort Mixed Fasteners In A Workshop

A box of mixed bolts from many machines is hard to sort by eye, because metric and inch bolts look alike at a glance. Measure each size once, note the identified thread on the bin, and the box becomes stock instead of scrap.

Every thread job needs the same two numbers, the diameter and the pitch, and this tool turns them into a standard thread name in seconds. That is the whole job for any bolt.

Advertisement

Quality And Settings

The result is only as good as the measurements that go into it. Measure the diameter with calipers across the thread crests, clean the threads first, and measure the pitch with a thread gauge where possible. Counting threads over 10 millimetres or one inch works well when no gauge is at hand, and counting over a longer length gives a more exact pitch.

  • Measure the major diameter across the crests, not the shank.
  • Clean dirt and rust from the threads before measuring.
  • Use a thread gauge for the pitch when one is available.
  • Count threads over 10 mm or 1 inch for a steadier pitch reading.
  • Download the summary before you clear the numbers.

When the match quality says exact and the measured diameter sits just under the nominal size, the thread is named with confidence. The Power Converter changes kilowatts into horsepower for the drive behind the joint.

How Thread Pitch Identifier Works

The identifier compares the measured diameter and pitch with two real standard tables. The metric table holds ISO 261 coarse and fine pitches from M1.6 to M36: M10 coarse is 1.5 millimetres with fine pitches of 1.25, 1.0, and 0.75 millimetres, and M12 coarse is 1.75 millimetres with fine pitches of 1.5, 1.25, and 1.0 millimetres. The inch table holds ASME B1.1 UNC and UNF sizes from number 0 to 1 inch: 3/8-16 UNC and 3/8-24 UNF share a 9.525 millimetre major diameter, and 1/4-20 UNC pairs with 1/4-28 UNF. The five closest candidates are shown with a match quality of exact, very close, or closest. The tap drill for a metric thread is the nominal diameter minus the pitch, which gives about 75 percent thread engagement.

Two honest limits are worth knowing. First, the tool identifies the thread by diameter and pitch only: it cannot tell left hand from right hand threads, and it does not cover pipe threads, extra fine UNEF threads, or special threads, so a thread outside the two tables returns the closest matches. Second, the match is an estimate from caliper readings, not a gauge check, so a thread gauge should confirm the size before a critical joint is ordered or cut. The Unified Thread Standard page lists the UNC and UNF sizes and pitches used in the inch table.

For the worked example, the measured diameter is 10 millimetres and the pitch is 1.5 millimetres. The metric table holds M10 coarse at 1.5 millimetres, so the identifier returns M10 by 1.5 coarse as an exact match, with 3/8-16 UNC as the next closest thread.

Privacy

Everything you calculate stays in your browser. Thread Pitch Identifier runs on your own computer, and nothing you type is uploaded to a server, stored, or shared with anyone. The tool does its job and shows the answer, and that is all it does.

Because no account is needed, there is no name, email, or history tied to what you do. Closing the tab ends the session, and the browser clears the numbers from memory. Your work stays yours, and nothing about it is kept, shared, or sold.

Tips

A few habits make Thread Pitch Identifier work smoother.

  • Measure the diameter first, then the pitch, in that order.
  • Try a thread gauge leaf until one sits crest to crest.
  • Check both metric and inch matches before you decide.
  • Write the identified thread on the part or the bin at once.
  • Download the summary before you clear the numbers.

When the match quality says exact and a nut of that size threads on smoothly by hand, the thread is confirmed. The Temperature Converter changes workshop temperatures between Celsius and Fahrenheit.

More Tools For The Same Job

These tools handle the same kinds of jobs: measuring, converting, and sizing threaded parts.

FAQ

Common questions about thread pitch and thread sizes, answered plainly.

Is Thread Pitch Identifier By TechnSols Free?

Yes, Thread Pitch Identifier by TechnSols is completely free to use, with no account, no sign-up, and no usage limit. You can identify as many threads as you like, and everything runs in your browser, so nothing is uploaded or stored anywhere.

What Is Thread Pitch?

Thread pitch is the distance between two neighbouring thread crests, measured along the bolt. Metric threads give it in millimetres, such as 1.5 millimetres for M10 coarse, while inch threads give it as threads per inch, such as 16 TPI for 3/8-16 UNC. The two are linked: pitch in millimetres equals 25.4 divided by TPI.

How Do I Measure Thread Pitch Without A Gauge?

Count the threads over 10 millimetres for a metric thread and divide 10 by the count, or count the threads over one inch for an inch thread to get TPI. Counting over a longer length gives a steadier result than measuring one pitch with a ruler, and a thread gauge is still the most exact way.

What Is The Difference Between Coarse And Fine Threads?

Coarse is the standard pitch for a diameter: M10 coarse is 1.5 millimetres, and the pitch may be left out of the name. Fine is a smaller pitch at the same diameter, such as M10 by 1.25, always written. Fine threads are stronger and resist vibration better, while coarse threads assemble faster and suit general work.

Can I Download My Thread Identification?

Yes, you can download the result as a short text summary with the Download button. The summary lists the measured diameter, the measured pitch, and the closest standard threads with their match quality, so it works as a record for the job.

Measure the diameter, measure the pitch, and read the thread name. A bolt ordered from that name threads in first time, and that is the whole point of the identification.

Follow TechnSols on Google
Add TechnSols as a preferred source to see more of our tools in Google Search.
Add to Preferred Sources
Advertisement