TechnSols
Advertisement

Beam Deflection Calculator

Beam Deflection Calculator: work out beam deflection free online. Simply supported or cantilever, no install or sign-up needed.

Be the first to rate this tool

Enter the load, length and section, then press Calculate Deflection.

What Is Beam Deflection Calculator?

Beam Deflection Calculator is a free online tool by TechnSols that works out how far a beam bends under load, and where the bend is greatest. Pick the support and load case, enter the load, the length, the material, and the second moment of area, and the tool gives the maximum deflection in millimetres and where it occurs.

Advertisement

A beam that bends too far cracks plaster, jams doors, and makes floors feel bouncy, even when it is strong enough not to break. Deflection is a serviceability problem, not a strength problem, so it must be checked on its own. When the load itself must be worked out first, the Force Calculator gives the force from mass and acceleration.

The tool covers four cases: a simply supported beam with a central point load, a simply supported beam with a uniform load, a cantilever with an end point load, and a cantilever with a uniform load. It also shows the deflection ratio, the length divided by the deflection, so the result can be compared with a limit such as L over 360. When a length must be changed between units before it is entered, the Length Converter changes millimetres into inches and back.

How To Use Beam Deflection Calculator?

Using Beam Deflection Calculator takes less than a minute, with no software to install and no account to make. Pick the case, enter the load and the length, pick the material, enter the section value, and read the answer. The defaults already hold a one metre steel beam.

Step 1: Pick The Support And Load Case

Pick the case that matches the beam: simply supported means the beam rests on a support at each end and can rotate there, while a cantilever is fixed at one end and free at the other. Then pick the load type: a point load acts at one place, while a uniform load spreads over the whole length. When a torque value must be changed between units for the same job, the Torque Unit Converter changes newton millimetres into newton metres and back.

Step 2: Enter The Load And The Length

Enter the load in newtons for a point load, or in newtons per millimetre for a uniform load, and enter the beam length in millimetres. A pressure acting on an area gives the load, and the Pressure Converter changes pascals into pounds per square inch. A uniform load of 1 newton per millimetre over a 1,000 millimetre beam is a total load of 1,000 newtons, so check the units before pressing the button.

Step 3: Pick The Material And Enter The Section

Pick the material, because the material sets the stiffness: steel uses 200 GPa, aluminium uses 69 GPa, and timber uses 11 GPa. Then enter the second moment of area in millimetres to the fourth power, taken from a section table or worked out from the shape. Press Calculate Deflection and read the maximum deflection, where it occurs, the maximum bending moment, and the deflection ratio.

The whole check is one calculation, and the numbers can be used straight in a design sheet.

Why Does Beam Deflection Matter?

Deflection matters because a beam can be strong enough to carry its load and still bend too far for the building around it. Floors that sag crack tiles and plaster, and beams that sag jam doors and windows. The limit is often a ratio such as the length divided by 360 for floors. The Deflection Page explains how deflection is measured and why serviceability limits exist.

The length matters most, because the deflection grows with the third power of the length for a point load and with the fourth power for a uniform load: a beam twice as long bends eight times as far under the same point load. When a force must be changed between units for the same calculation, the Force Unit Converter changes newtons into pounds force and back.

What Happens When A Beam Bends Too Far?

A beam that bends too far damages everything attached to it. Plaster cracks, tiles lift, and doors stick in their frames. The beam itself may still be far from failure, but the building around it is not usable.

How Does A Cantilever Compare With A Simply Supported Beam?

A cantilever bends far more than a simply supported beam of the same length, section, and load. With a point load at the end, a cantilever deflects sixteen times as far as a simply supported beam with the same load at mid span, because the formulas differ by 3 against 48 in the denominator.

What Is The Second Moment Of Area?

The second moment of area, written as I, is a property of the cross section shape that says how well the shape resists bending. A deep section has a much larger value than a shallow one of the same area. For a rectangle of width b and depth h, the value is b times h to the third power divided by 12, so doubling the depth makes the beam eight times as stiff.

What Can You Do With Beam Deflection Calculator?

Beam Deflection Calculator fits any job where a beam must be checked for sag before it is built.

Check A Floor Beam For Sag

A floor beam carries a uniform load from the floor above, and the check is whether the sag stays inside the limit for the finishes. Enter the load, the span, the material, and the section value, and the calculator gives the sag at mid span and the ratio. When the cross section area must be known for a weight check, the Area Converter changes square millimetres into square inches.

Check A Cantilever Bracket

A cantilever bracket carries a point load at its free end, such as a machine or a sign, and the check is the deflection at the free end. A cantilever deflects sixteen times as far as a simply supported beam under the same load, so the section must be much deeper.

Compare Steel, Aluminium, And Timber

The same beam in aluminium instead of steel deflects about three times as far, because aluminium at 69 GPa is about a third as stiff as steel at 200 GPa. Timber at 11 GPa deflects about eighteen times as far as steel for the same section. When the volume of the beam must be worked out for a weight estimate, the Volume Converter changes cubic millimetres into cubic centimetres.

Every beam job needs the same number, the maximum deflection, and this tool gives it from the same five inputs. That is the whole job, and it takes less than a minute for any beam.

Advertisement

Quality And Settings

The quality of a beam deflection result depends on the quality of the five inputs, because the formulas are exact and only the inputs can be wrong. A correct case, a correct load, a correct span, the right material, and the right section value give a result that matches a textbook.

  • Pick the case that matches the real supports, because a cantilever checked as simply supported gives a deflection sixteen times too small.
  • Check the load units: newtons for a point load, newtons per millimetre for a uniform load, and never mix the two.
  • Measure the span between supports for a simply supported beam, and from the wall to the free end for a cantilever.
  • Take the second moment of area from a section table for the exact section, not from a section that looks similar.
  • Compare the deflection ratio with the limit for the job, such as L over 360 for floors, before accepting the beam.

When a value must be changed between unit systems for a second check, the Unit Converter changes the units in seconds. A result that looks wrong usually traces back to one of these five points, and the most common fault is entering a uniform load as a total load.

How Beam Deflection Calculator Works

The calculator uses the standard Euler Bernoulli formulas for a beam that is linear elastic, uniform along its length, and loaded by one static load. A simply supported beam with a central point load deflects by the load times the length cubed divided by 48 times E times I, at mid span, with a maximum moment of the load times the length divided by 4. A simply supported beam with a uniform load deflects by 5 times the load times the length to the fourth power divided by 384 times E times I, at mid span, with a maximum moment of the load times the length squared divided by 8. A cantilever with an end point load deflects by the load times the length cubed divided by 3 times E times I, at the free end, with a maximum moment of the load times the length. A cantilever with a uniform load deflects by the load times the length to the fourth power divided by 8 times E times I, at the free end, with a maximum moment of half the load times the length squared. The Second Moment Page explains how the second moment of area is worked out.

Two honest limits are worth knowing. First, the tool checks deflection only: it does not check bending or shear strength, buckling, or any design code limit, so a beam that passes the deflection check still needs a strength check. Second, the formulas assume a single static load on a uniform beam, so a beam with several loads or a changing section needs a full structural check.

For the worked example, a simply supported beam carries a central point load of 1,000 newtons over a span of 1,000 millimetres, the steel has E of 200,000 MPa, and the section has I of 83,333 millimetres to the fourth power. The deflection is 1,000 times 1,000,000,000 divided by 48 times 200,000 times 83,333, giving 1.25 millimetres at mid span. The maximum moment is 1,000 times 1,000 divided by 4, which is 250,000 newton millimetres, and the deflection ratio is L over 800.

Privacy

Everything you calculate stays in your browser. Beam Deflection Calculator runs on your own computer, and nothing you type is uploaded to a server, stored, or shared with anyone.

Because no account is needed, there is no name, email, or history tied to what you do. Closing the tab ends the session, and the browser clears the numbers from memory.

Tips

A few habits make Beam Deflection Calculator work smoother.

  • Check the case first, because the wrong case gives a wrong answer by a large factor.
  • Double the depth before you change the material when a beam is too flexible.
  • Keep the load units straight, and write N or N per mm next to every load value.
  • Compare the ratio with the job limit, not just the millimetres, because a long beam allows more sag than a short one.
  • Download the summary before you clear the numbers.

When the deflection sits inside the limit, the beam is ready for its strength check. If the power of a machine on the beam needs checking, the Power Converter changes watts into horsepower.

More Tools For The Same Job

These tools handle the same kinds of jobs: forces, sizes, and structural design numbers.

FAQ

Common questions about beam deflection and beam design, answered plainly.

Is Beam Deflection Calculator By TechnSols Free?

Yes, Beam Deflection Calculator by TechnSols is completely free to use, with no account, no sign-up, and no usage limit. You can work out as many beams as you like, and everything runs in your browser. No file is uploaded anywhere, and no result is stored on any server.

What Is Beam Deflection?

Beam deflection is how far a beam bends under load, measured in millimetres at the point where the bend is greatest. It depends on the load, the span, the material stiffness, and the second moment of area of the section.

Where Does Maximum Deflection Occur?

For a simply supported beam, the maximum deflection is at mid span. For a cantilever, the maximum deflection is at the free end. The calculator states the place with every result, so the check is never guessed. Knowing the place matters, because that is where the clearance and the fit must be checked first.

Why Is A Cantilever Deflection So Much Larger?

A cantilever is fixed at one end only, so the whole beam bends from the wall outward, while a simply supported beam is held at both ends. With the same point load, a cantilever deflects sixteen times as far as a simply supported beam, because the formulas differ by 3 against 48 in the denominator.

Can I Download My Beam Calculation?

Yes, you can download the result as a short text summary with the Download button. The summary lists the case, the load, the length, the material, the section, the deflection, and the moment, so it works as a record for the job.

Pick the case, enter the load and the section, and read the deflection. A beam checked this way fits the building first time.

Follow TechnSols on Google
Add TechnSols as a preferred source to see more of our tools in Google Search.
Add to Preferred Sources
Advertisement