TechnSols
Advertisement

Die-Cut Shape Designer

Cut shapes with exact bleed lines

Be the first to rate this tool

Pick a shape and size, then press Design Die-Cut Shape.

What Is Die-Cut Shape Designer?

Die-Cut Shape Designer is a free online tool by TechnSols that designs die-cut shapes from exact numbers: pick a rectangle, circle, rounded rectangle, diamond, or triangle, type its width and height, set the corner radius and the bleed, and the tool draws the cut line and the bleed outline as a true size SVG and PNG. The cut line is the line the blade follows, and the bleed outline is the same shape grown outward by the bleed amount, so the artwork reaches past the cut and no white edge shows.

Advertisement

A die-cut shape is cut by a steel die or a plotter blade, and the cutter needs a closed vector path, not a picture. This designer builds that path from numbers, so every line is exact: a rounded rectangle 80 mm wide and 50 mm tall, with an 8 mm corner radius and 3 mm of bleed, has a bleed size of 86.00 by 56.00 mm and a cut area of 3945.06 square millimetres. The shape is drawn at true size in millimetres, so it opens at the right size in a design program. If you need to check a bleed area first, the Bleed Area Calculator works out bleed size and area from trim size and bleed margin.

Everything runs in your browser, and no file is uploaded anywhere. You type the numbers, press Design Die-Cut Shape, and the tool draws the shape at once, with both downloads ready on the same page.

How To Use Die-Cut Shape Designer?

Using Die-Cut Shape Designer takes about a minute, with no software to install and no account to make. Pick a shape, type its size, set the bleed, and download the SVG and the PNG. If a size arrives in inches, the Unit Converter changes it into millimetres first.

Step 1: Pick A Shape And Its Size

Pick one of the five shapes: Rectangle, Circle, Rounded Rectangle, Diamond, or Triangle. Type the width and the height in millimetres, using the defaults of 80 mm wide and 50 mm tall. For a circle, the width is the diameter, and the height follows it. For a rounded rectangle, type the corner radius as well, with 8 mm as a starting point, and keep it no larger than half of the smaller side. If the shape is artwork that needs a format change first, the Image Converter changes an image from one format to another.

Step 2: Set The Bleed Around The Shape

Type the bleed in millimetres, with 3 mm as a good starting point for most print and cut jobs. The bleed outline grows outward from the cut line by that amount on every side, so a shape 80 by 50 mm with 3 mm of bleed becomes 86 by 56 mm overall. A larger bleed suits a cutter that may drift slightly, while a smaller bleed suits a tight layout where shapes sit close together. Set the bleed to zero when the shape needs no bleed at all, such as a shape cut from plain vinyl.

Step 3: Design The Shape And Download It

Press Design Die-Cut Shape to draw the shape: the bleed outline shows as a dashed red shape, and the cut line shows as a solid blue shape inside it. Read the results table for the cut size, the bleed size, the bleed amount, and the cut area. Download the SVG for a design program or a cutting machine, because it is a vector file at true size, and download the PNG for a quick print or a visual check. With 2 outputs, Download all files saves both at once.

The whole job is three steps, and you can change the shape or the size and design again as often as needed.

Why Do Die-Cut Shapes Need Exact Lines?

A die-cut shape is made by a blade that follows a path, and the blade cannot guess. When the path is open, wobbly, or the wrong size, the cut is wrong on every piece, and the whole sheet is wasted. Exact lines turn a cut job into a numbers job, and a numbers job is easy to get right.

The Blade Follows The Cut Line Only

A cutting machine reads the vector path and moves the blade along it, so the path must be one closed shape with no gaps. A picture of a shape has no path at all, which is why a PNG alone cannot drive a cutter. This designer builds the path from numbers, so the SVG it exports is a closed shape the machine can follow.

Bleed Stops White Edges Showing

Printers and cutters drift by a fraction of a millimetre, and when the artwork ends exactly at the cut line, that drift leaves a thin white edge on the finished piece. Bleed is artwork that runs past the cut line, so a small drift still cuts through colour. Three millimetres of bleed suits most jobs, and the designer grows the bleed outline outward by exactly that amount.

Rounded Corners Need A Real Radius

A rounded corner is an arc with a real radius, and a radius guessed by eye looks different on every piece. Typing the radius, such as 8 mm, makes every corner the same, and the bleed outline grows the radius by the bleed amount as well, so the bleed follows the cut line evenly all the way around. If the cut area needs changing into other units, the Area Converter changes it into square centimetres or square inches.

What Can You Do With Die-Cut Shape Designer?

Die-Cut Shape Designer fits any job where a shape must be cut exactly. These are the jobs it handles best, from a single sticker to a full sheet of labels.

Design A Die-Cut Sticker Shape

Pick a rounded rectangle or a circle, type the sticker size, and set 3 mm of bleed. The SVG gives the cutter a closed cut line with a bleed outline, and the PNG gives a picture to check the proportions before cutting. A sticker 80 by 50 mm with 3 mm of bleed cuts cleanly with no white edge showing.

Make A Hang Tag Or A Label Shape

A hang tag is often a rectangle with rounded corners, and a label is often a circle or a diamond. Type the size, set the corner radius for a tag, and download the SVG to place the artwork inside the cut line. The bleed outline shows where the artwork must reach, so the printed tag has colour right up to the cut edge.

Plan A Sheet Of Cut Shapes

Before cutting a full sheet, design one shape and check its bleed size against the sheet, so you know how many shapes fit and how much space the bleed needs between them. A shape with a bleed size of 86 by 56 mm needs at least that much room, plus a gap for the blade.

Every job that starts with a shape and a size ends with a cut line a machine can follow, and this tool draws it in the browser. That is the whole job, and it takes less than a minute for any shape. When the shape needs a sheet of cards to go with it, the Business Card Arranger arranges cards on a printable sheet. A matching barcode for the finished pack can be made with the Barcode Generator tool.

Advertisement

Quality And Settings

Five settings shape the die-cut shape, and each one is simple to set.

  • Shape: rectangle, circle, rounded rectangle, diamond, or triangle, default rounded rectangle.
  • Shape width: 1 to 1000 mm, the diameter for a circle, default 80 mm.
  • Shape height: 1 to 1000 mm, follows the width for a circle, default 50 mm.
  • Corner radius: 0 to 500 mm, for rounded rectangles only, default 8 mm.
  • Bleed: 0 to 50 mm on every side, default 3 mm, zero for no bleed.

The SVG is drawn at true size in millimetres, with a 10 mm margin around the whole drawing. The bleed outline is dashed red, the cut line is solid blue, and a label under the shape names the shape, the cut size, and the bleed. When the shape also needs a sheet layout, the Barcode Label Sheet arranges items on a printable sheet.

How Die-Cut Shape Designer Builds The Shape

The designer builds the shape from the numbers you type. A rectangle is four straight sides, a circle is one diameter, a rounded rectangle is four sides joined by arcs of the corner radius, a diamond is four points at the top, right, bottom, and left, and a triangle is three points at the top and the two bottom corners. The bleed outline is built the same way, grown outward by the bleed amount: a rectangle grows by the bleed on every side, a circle grows its radius by the bleed, and a diamond or triangle moves each point outward by the bleed. For the default rounded rectangle, the cut area is 3945.06 square millimetres. The SVG Editor opens the exported SVG for a closer look at the paths.

Two honest limits are worth knowing. First, this designer builds five exact shapes from numbers only, and it does not trace uploaded artwork, so a logo outline or a photo shape needs a tracing tool that turns pixels into paths. Second, the SVG is a shape with a cut line and a bleed outline, not finished artwork, so the design, the text, and the images still need a design program. If the shape needs a code printed on it, the QR Code Generator makes a code for the label.

Privacy

Everything you type stays in your browser. Die-Cut Shape Designer runs on your own computer, and nothing you enter is uploaded to a server, stored, or shared with anyone. The tool draws the shape locally, and that is all it does.

Because no account is needed, there is no name, email, or history tied to what you do. Closing the tab ends the session, and the browser clears the numbers from memory. Your shape sizes and cut plans stay yours, and nothing about them is kept, shared, or sold.

Tips

A few habits make Die-Cut Shape Designer work smoother.

  • Cut one test shape first, before cutting a full sheet.
  • Keep text and logos inside the cut line, clear of the bleed area.
  • Check that the SVG opens at true size in your cutting software.
  • Set fold or score lines to score, not cut, in the cutting software.
  • Save the SVG with the product file, as a record of the shape and bleed.

When the test shape cuts cleanly, the bleed covers the edge, and the size measures true, the shape is ready.

More Tools For The Same Job

These tools handle the same kinds of jobs: shapes, labels, packaging, and print sizes.

FAQ

Common questions about die-cut shapes and this designer, answered plainly.

Is Die-Cut Shape Designer By TechnSols Free?

Yes, Die-Cut Shape Designer by TechnSols is completely free to use, with no account, no sign-up, and no usage limit. You can design as many shapes as you like, and everything runs in your browser, so nothing is uploaded or stored anywhere.

What Is A Die-Cut Shape?

A die-cut shape is a shape cut by a steel die or a plotter blade along a closed vector path, called the cut line. The cut line tells the blade exactly where to cut, and the bleed outline shows where the artwork must reach past the cut, as the Die Cutting guide explains.

What Bleed Should I Use?

Use 3 mm of bleed for most print and cut jobs, because it covers the small drift of printers and cutters without wasting material. Use more bleed for a cutter that drifts further, and zero bleed for plain vinyl or card with no printed artwork to protect.

Can I Use The SVG In Cricut Or Silhouette?

Yes, the SVG is a closed vector shape at true size in millimetres, so it opens in Cricut Design Space and Silhouette Studio as a cut shape. Set the dashed bleed outline to a print layer or delete it before cutting, so the blade follows the solid cut line only, as the Sticker Cut Line guide explains.

Does The Designer Trace Uploaded Artwork?

No, it builds five exact shapes from the numbers you type, and it does not trace uploaded artwork. A logo outline or a photo shape needs a tracing tool that turns pixels into paths, while this designer is for shapes where the size and the bleed must be exact.

Pick a shape, set the bleed, and cut one test piece first. A shape designed here cuts cleanly, and that is the whole point of the designer.

Follow TechnSols on Google
Add TechnSols as a preferred source to see more of our tools in Google Search.
Add to Preferred Sources
Advertisement