What Is Bolt Circle Calculator?
Bolt Circle Calculator is a free online tool by TechnSols that turns a bolt circle diameter, a hole count, a first hole angle and a hole diameter into the exact angle and X and Y position of every hole in the pattern. A flange, a wheel hub, a motor mount or a pipe flange needs holes that line up with the mating part, and a single wrong coordinate means the bolts will not pass through, so this tool removes the hand calculation and the risk that comes with it.
A bolt circle, also called a pitch circle, is the imaginary circle that passes through the centre of every hole in a circular pattern. The bolt circle diameter, written as PCD or BCD, is the diameter of that circle. Once the diameter and the hole count are known, every hole sits at the same radius from the centre, spaced by the same angle, The tool does that maths for every hole at once, draws the pattern as a diagram, and gives the results as a CSV file for a spreadsheet or a CNC program.
Everything runs in your browser, and no file is uploaded anywhere. The calculator works with millimetres, which is the unit most workshops use for flanges and hubs, and the diagram shows the circle, the centre cross, the hole numbers and the hole sizes, so the pattern can be checked by eye before any metal is cut. If a drawing needs to move between formats first, the SVG To DXF tool changes an SVG drawing into DXF, while the DXF To SVG tool changes a DXF file back into SVG for viewing.
How To Use Bolt Circle Calculator?
Using Bolt Circle Calculator takes less than a minute, with no software to install and no account to make. Enter four numbers, press Calculate Bolt Circle, and read the table, the diagram and the files. The worked example below uses a 100 mm bolt circle with 6 holes, first hole at 0 degrees and a 10 mm hole diameter.
Step 1: Enter The Bolt Circle Diameter And Hole Count
Type the bolt circle diameter in millimetres into the first box, then type the number of holes into the second box. The diameter must be over 0 and up to 10000 mm, and the hole count must be a whole number from 2 to 360. For the worked example, enter 100 for the diameter and 6 for the hole count, which gives a radius of 50 mm and an angle step of 60 degrees. If the diameter is written in another unit, the Unit Converter changes inches, centimetres or feet into millimetres first.
Step 2: Set The First Hole Angle And Hole Diameter
Type the angle of the first hole in degrees into the third box, then type the hole diameter in millimetres into the fourth box. Angle 0 puts the first hole on the positive X axis, angle 90 puts it at the top, and any angle from minus 360 to 360 is accepted, so the whole pattern can be rotated to match a drawing. The hole diameter must be smaller than the bolt circle diameter, and it sets the size of the circles drawn in the diagram. For the worked example, enter 0 for the first hole angle and 10 for the hole diameter.
Step 3: Read The Table, Diagram And Files
Press Calculate Bolt Circle to see the results. The table lists every hole with its angle and its X and Y coordinates to two decimal places, and the diagram draws the bolt circle with each hole numbered. For the worked example, hole 1 sits at angle 0 with coordinates 50.00 and 0.00, hole 2 sits at angle 60 with coordinates 25.00 and 43.30, and hole 3 sits at angle 120 with coordinates minus 25.00 and 43.30. Download the CSV file for the full table or the SVG file for the diagram, or press Download all files to save both at once.
Why Do Engineers Need A Bolt Circle Calculator?
A circular bolt pattern looks simple, yet it is easy to get wrong by hand, because every hole needs its own sine and cosine, and one slipped digit moves a hole by millimetres. A calculator that shows every coordinate, the angle step and the chord between neighbouring holes gives a result that can be checked line by line before drilling.
Hand Maths Is Slow And Error Prone
With 6 holes, a careful engineer needs 12 trigonometric calculations, and with 12 or 24 holes the count doubles or quadruples. The calculator does the same work in a moment, and it shows the angle step beside the coordinates, so a wrong input stands out at once: a step of 60 degrees belongs to 6 holes, a step of 45 degrees belongs to 8 holes. When a length needs converting before it is entered, the Length Converter changes it between millimetres, centimetres, metres and inches.
Flanges Must Mate Exactly
Two flanges bolt together only when every hole in one lines up with the matching hole in the other, and a pattern drilled even half a millimetre out can leave a bolt that will not pass through. The calculator gives coordinates to two decimal places, and the chord it reports is the straight distance between neighbouring hole centres, which can be checked on the finished part with calipers. If the part also needs its size checked in three dimensions, the Dimension Viewer shows the dimensions of an STL model.
One Pattern Serves Many Machines
The same coordinate table serves a drill press, a mill, a CNC machine and a laser cutter, because each one takes X and Y positions from the same centre.
What Can You Do With Bolt Circle Calculator?
Bolt Circle Calculator fits any job where holes sit evenly around a circle. These are the jobs it handles best, from a small bracket to a large industrial flange.
Drill A Flange That Bolts Up First Time
A pipe flange with 8 holes on a 200 mm bolt circle needs each hole at 45 degree steps, and the calculator lists all 8 positions in one table. Mark the centre, mark the X and Y of each hole from the table, drill, and the mating flange lines up, because the coordinates came from one calculation instead of eight separate hand sums.
Check A Wheel Hub Pattern
Wheel hubs use patterns such as 4 by 100, 5 by 114.3 and 6 by 139.7, where the first number is the hole count and the second is the bolt circle diameter in millimetres. Enter those two numbers, and the calculator shows whether the pattern on the bench matches the pattern on the drawing, hole by hole, before a wheel is ever fitted. When the job time also needs planning, the Time Estimator estimates how long a 3D print of a prototype hub will take.
Program A CNC Hole Pattern
A CNC program needs the X and Y of every hole, and typing those numbers by hand is where most programming slips happen. The CSV file from this tool carries the full table, so the numbers can be copied into the program or checked against it, and the SVG diagram gives the operator a picture of the pattern to compare with the finished part.
Quality And Settings
Four settings shape the bolt circle, and each one is simple to set.
- Bolt circle diameter: 0.01 to 10000 mm, entered in millimetres.
- Number of holes: a whole number from 2 to 360.
- First hole angle: minus 360 to 360 degrees, measured from the positive X axis, counter-clockwise positive.
- Hole diameter: 0 or more, smaller than the bolt circle diameter, sets the drawn hole size.
- Outputs: a coordinate table, an SVG diagram, a CSV file and an SVG file.
The 360 hole limit keeps the table readable in the browser, and patterns larger than that are rare in real parts. When a drawing image needs a format change before it is measured, the Image Converter changes it from one image format to another.
How Bolt Circle Calculator Finds Each Hole
The calculator starts from the bolt circle diameter and halves it to get the radius, then divides 360 degrees by the hole count to get the angle step. Hole 1 sits at the first hole angle, hole 2 sits one step further round, hole 3 sits two steps further round, and so on until every hole is placed. For each hole, X equals the radius times the cosine of the hole angle, and Y equals the radius times the sine of the hole angle, with angles measured from the positive X axis and counter-clockwise positive. The chord between neighbouring holes is twice the radius times the sine of 180 degrees divided by the hole count, which is 50.00 mm for the worked example.
Two honest limits are worth knowing. First, the tool only builds evenly spaced patterns, so a pattern with irregular spacing, a missing hole or an offset hole cannot be described by it, and such a pattern needs a drawing tool instead. Second, the coordinates are exact geometry from the entered numbers, so they are only as good as the measurements behind them: a diameter measured from hole edges instead of hole centres will give a wrong pattern, and the result should always be checked against the real part. If a finished drawing needs to be shared as a PDF, the SVG To PDF tool makes a PDF copy, and the PDF To Image tool turns a PDF page back into an image.
Privacy
Everything you enter stays in your browser. Bolt Circle Calculator runs on your own computer, and nothing you type is uploaded to a server, stored, or shared with anyone. The tool reads the four numbers, works out the coordinates, and draws the diagram locally, and that is all it does.
Because no account is needed, there is no name, email, or history tied to what you do. Your drawings and dimensions stay yours, and nothing about them is kept, shared, or sold.
Tips
A few habits make Bolt Circle Calculator work smoother.
- Measure the bolt circle diameter from hole centre to hole centre, never from edge to edge.
- Check the angle step first, since it confirms the hole count at a glance.
- Use angle 0 for a hole on the positive X axis, or 90 for a hole at the top.
- Check the chord on the finished part with calipers before assembly.
- Save the CSV with the job, so the pattern can be remade without retyping numbers.
More Tools For The Same Job
These tools handle the same kinds of jobs: CAD drawings, CNC work, dimensions and units.
- DXF File Viewer: draws an uploaded DXF file as a 2D vector drawing with pan and zoom.
- G-Code Toolpath Visualizer: previews G-code and draws the CNC toolpath with depths.
- SVG To G-Code Converter: turns SVG paths into G-code for a CNC machine or laser.
- 2D Technical Drawing Board: draws lines, circles, arcs and dimensions on a CAD style canvas.
- Dimension Annotation Generator: adds dimension arrows and measurements to a drawing.
- Scale Drawing Calculator: converts between real size and paper size at a drawing scale.
- Sheet Metal Bend Allowance Calculator: works out bend allowance and deduction for sheet metal.
- CNC Cutting Time Estimator: estimates CNC job time from toolpath length and feed rates.
- STL Model Dimension Viewer: shows the dimensions of a 3D STL model file.
- Unit Converter: changes lengths, weights and other units before they are entered.
FAQ
Common questions about bolt circles and this calculator, answered plainly.
Is Bolt Circle Calculator By TechnSols Free?
Yes, Bolt Circle Calculator by TechnSols is completely free to use, with no account, no sign-up, and no usage limit. You can calculate as many bolt patterns as you like, and everything runs in your browser, so nothing is uploaded or stored anywhere.
What Is A Bolt Circle Diameter?
The bolt circle diameter is the diameter of the imaginary circle that passes through the centre of every hole in a circular pattern. It is also called the pitch circle diameter, and a pattern is often written as the hole count followed by the diameter, such as 6 by 100 for 6 holes on a 100 mm circle.
How Are The Hole Coordinates Worked Out?
Each hole sits at the radius, which is half the bolt circle diameter, at its own angle. The angle of hole n is the first hole angle plus n minus 1 times the angle step of 360 divided by the hole count. X is the radius times the cosine of that angle, and Y is the radius times the sine.
What Does The Chord Tell Me?
The chord is the straight line distance between the centres of two neighbouring holes, and it equals twice the radius times the sine of 180 degrees divided by the hole count. It is a handy check on a finished part, because it can be measured directly with calipers between two adjacent holes.
Where Can I Read More About Bolt Circles?
A bolt circle is a common feature on flanges, wheels and hubs, where evenly spaced holes must line up with a mating part. The Bolt Circle guide explains the pattern and its uses, and the Flange guide explains how flanges use bolt circles to join pipes and parts.
Enter the diameter, the hole count, the first angle and the hole size, then check the table and the diagram.