TechnSols
Advertisement

Stereo Phase Checker

Check stereo phase correlation free online. Stereo Phase Checker measures mono compatibility with a phase meter and report. No install, no sign-up.

Be the first to rate this tool

Drop a stereo audio file here, or

MP3, WAV, OGG, FLAC, M4A, AAC or Opus.

Choose a stereo audio file to check its phase.

What Is Stereo Phase Checker?

Stereo Phase Checker is a free online tool by TechnSols that measures how well the left and right channels of a stereo audio file work together. Upload a stereo file, and the tool calculates the phase correlation between the two channels, shows it on a meter from minus 1 to plus 1, and gives a mono compatibility verdict, so you can tell at a glance whether your mix will survive when it is played back in mono.

Advertisement

Two channels can sound wide and full on speakers and still cancel each other out when they are summed to mono. A bass line that is out of phase disappears on a phone speaker, a vocal that is spread too wide goes thin on a smart speaker, and a mix that was never checked in mono can lose its low end on a club system. The ear cannot hear the correlation number, and a stereo meter only shows levels. This checker measures that relationship directly, using the same Web Audio API that browsers use to decode audio.

The tool works with common audio formats such as MP3, WAV, OGG, FLAC, M4A, AAC, and Opus. It decodes the file in your browser and compares the left and right channels sample by sample with the Pearson correlation, a standard measure that returns plus 1 when the channels are identical, 0 when they are unrelated, and minus 1 when they are exact opposites. The same measurement is repeated on the low frequencies below 150 Hz, because bass is where a phase problem hurts most. A quick check of the stereo balance can also show whether one channel is simply louder, which is a different problem from phase.

How To Use Stereo Phase Checker?

Step 1: Choose A Stereo Audio File

Drop your stereo audio file onto the tool, or press the button to choose it from your device. Files up to 100 MB are accepted, and audio up to 30 minutes long can be analysed. The file is read in your browser and never uploaded anywhere, so an unreleased mix stays private. Once the file is decoded, the tool shows its length and channel count. A file with one channel is refused with a clear message, because a mono file has no stereo phase to measure.

Step 2: Press Check Phase

Press Check Phase. The tool measures the overall correlation, the low band correlation below 150 Hz, the peak and RMS level of each channel, the share of the file that is out of phase, and the level lost when the channels are summed to mono. The whole analysis takes a few seconds for a normal length song, and there are no settings to adjust, because the measurement is the same for every file.

Step 3: Read The Meter And The Report

The phase meter shows the overall correlation on a gauge from minus 1 to plus 1, with coloured zones for out of phase, weak, good, and excellent. Below it, a chart plots the correlation over time in 50 millisecond windows, so you can see whether a problem lasts the whole file or sits in one section. The results list gives every number with a short label, and a plain text report is ready to download. Open the file in an audio spectrum analyzer to see which frequencies are involved, or view the audio waveform to find the exact moment a problem starts.

Why Check Stereo Phase?

Mono playback is everywhere. Phones, smart speakers, televisions, and club systems often sum stereo to mono, and a listener who stands to one side of a pair of speakers hears a mix that is closer to mono than to true stereo. If the two channels cancel each other, the summed sound loses level, and the loss is worst in the bass, where the wavelengths are long and the channels are usually meant to match. A mix that measures plus 0.8 keeps almost all of its level in mono, while a mix that measures minus 0.5 can lose most of its bass entirely.

Phase problems usually come from a small mistake: a cable wired backwards, a microphone placed on the wrong side of a drum, a stereo widener pushed too far, or a plugin that delays one channel by a few samples. Each of those is easy to fix once it is found, and hard to find by ear, because the stereo version sounds fine and the problem only appears in mono. Measuring the correlation turns a vague worry into a number. The idea is the same one behind professional correlation meters, which show the phase relationship between channels as a single value that producers watch while they mix.

Checking phase is a habit that protects a release. A track that passes the check will sound the same on a phone, a car stereo, and a club system, while a track that fails will sound different on each one. The check takes seconds, and it catches a class of problem that no amount of equalisation can fix after the fact. A quick listen on real speakers confirms what the numbers say.

What Can You Do With Stereo Phase Checker?

Check A Mix Before Release

Run the final mix through the checker before you publish it. A verdict of good or excellent means the mix is safe for mono playback, while a weak or out of phase verdict means you should open the mix again and find the track that is causing it. The check is fast enough to run on every bounce.

Catch A Polarity Flip In A Recording

A microphone cable wired backwards flips the polarity of one channel, which shows up as a strongly negative correlation. The meter makes the flip obvious, and the chart shows whether it affects the whole file or only one section. Fix the cable or flip the polarity in your editor, then check again.

Protect Bass When A Track Goes Mono

Bass should be nearly identical in both channels, so the low band correlation below 150 Hz should be close to plus 1. If the low band reads much lower than the overall value, the bass is spread too wide, and it will thin out on mono playback. Narrow the bass, check again, and watch the low band climb toward plus 1.

Compare Two Mixes Of The Same Song

Check the old mix and the new mix side by side. The correlation numbers, the out of phase share, and the mono loss give you three numbers to compare, which is more reliable than memory. The mix with the higher correlation and the lower mono loss is the safer one for mono playback.

Verify A Stereo File After Conversion

Converting a file can change its channels, especially when a stereo file is resampled or re-encoded. Check the converted file and compare the numbers with the original. If the correlation dropped, the conversion did something to the phase, and you should try a different encoder or setting.

Learn How Stereo Width Affects Mono

Take a mix, widen it in your editor, and check it again. Watch the correlation fall and the mono loss grow as the width increases, and watch them recover as you narrow it. The numbers teach the trade off between width and mono safety faster than any amount of reading. A small change to the audio trim can isolate one section to test on its own, and a check of the audio volume shows whether the level loss is real.

Quality And Settings

The verdict bands are simple. A correlation of plus 0.7 or higher is excellent mono compatibility, plus 0.3 to plus 0.7 is good, 0 to plus 0.3 is weak, and anything below 0 is out of phase. Most finished mixes sit between plus 0.3 and plus 0.8, because a mix with a correlation of plus 1 is effectively mono and has no stereo width at all. A value in the good range is a healthy mix, not a problem to fix.

Advertisement

The low band number deserves its own attention. It is measured after a 150 Hz low pass filter, so it only reflects the bass. Bass that is out of phase is the most audible problem in mono, because the low end carries the weight of the mix. If the overall correlation is good but the low band is low, fix the bass first and leave the rest alone. A guitar tuner helps when you re-record a part, because a part in tune is easier to place without widening it.

How Stereo Phase Checker Works

When you choose a file, the browser decodes it with the Web Audio API into raw samples for each channel. The tool computes the Pearson correlation between the left and right channels over the whole file, which is the sum of the products of the two channels divided by the square root of the product of their energies. The same calculation is repeated on low passed copies of both channels, using a one pole filter at 150 Hz. Both numbers are exact for the decoded samples, so the same file always gives the same result.

The chart is built from 50 millisecond windows, each with its own local correlation. Windows with a negative local correlation are counted, and the share of such windows is reported as the out of phase percentage. The mono loss is measured by averaging the two channels into a mono signal, taking its RMS level, and comparing it with the RMS level of the louder channel, expressed in decibels. A loss of 0 dB means nothing disappears in mono, and a loss near 60 dB means the channels almost fully cancel. A variable bitrate MP3 still gives exact sample positions, so the measurements stay accurate.

Privacy

Your audio never leaves your device. The file is decoded and measured inside your browser, and no part of it is uploaded to any server. That matters for unreleased music, client mixes, and any file that must stay confidential. Closing the page removes the decoded audio from memory, and nothing is stored in a cookie or a database.

There is no account, no sign up, and no email address needed. The tool does not keep a history of what you analysed. Because everything runs locally, the tool also works on a slow connection once the page has loaded.

Tips

Check the whole mix, not a single stem. A single instrument can be out of phase on its own while the full mix measures fine, because the other instruments mask it. If the verdict is weak, solo the tracks one at a time and check each one until you find the one that pulls the number down.

Use the chart to find where the problem lives. A flat line near plus 1 with a dip in one section points to a single event, such as a stereo effect that only runs in the chorus, while a line that wanders below 0 for the whole file points to a wiring or polarity problem at the source. Fix the section, bounce again, and check the new file. If the file is very large, convert it to a smaller WAV file first, since a smaller file decodes faster.

More Tools For The Same Job

If you work with stereo audio, these free tools cover the next steps after checking phase: balancing the channels, trimming the file, and converting it into the format you need.

FAQ

Is Stereo Phase Checker By TechnSols Free?

Yes, Stereo Phase Checker by TechnSols is completely free to use, with no account, no sign up, and no limits on how many files you check. It runs entirely in your browser, it works with common audio formats, and the phase report download is free as well.

Which Audio Formats Can I Check?

You can check MP3, WAV, OGG, FLAC, M4A, AAC, and Opus files, up to 100 MB in size and up to 30 minutes long. The file must be a real stereo audio file, so a renamed text file or image is refused with a clear message. If your browser cannot decode a format, try converting it to MP3 first.

What Correlation Value Should I Aim For?

Aim for plus 0.3 or higher for the overall correlation, with plus 0.7 or higher being excellent. Most finished mixes sit between plus 0.3 and plus 0.8, and the low band below 150 Hz should be higher than the overall value. A value below 0 means the channels are out of phase and the mix needs fixing.

Why Does My File Sound Fine But Score Low?

A low score does not mean the file sounds bad in stereo, it means the file will lose level when it is played in mono. Stereo playback hides phase problems because each ear hears one channel, while mono playback sums the channels and lets them cancel. The score measures mono safety, not stereo quality.

Can I Check A Mono Audio File?

No, a mono file has only one channel, so there is no second channel to compare it with and no phase to measure. The tool refuses mono files with a clear message. If you want to check a mono recording, first check whether it was made from a stereo source, and analyse the stereo original instead.

Upload a stereo mix, read the meter, and check the low band. A mix that holds its correlation in mono will sound the same on every speaker, and that is the whole point of checking phase.

Follow TechnSols on Google
Add TechnSols as a preferred source to see more of our tools in Google Search.
Add to Preferred Sources
Advertisement