TechnSols
Advertisement

Gear Ratio Visualizer

Gear Ratio Visualizer free online: work out gear ratio, output RPM and torque from tooth counts. No install, no sign-up, runs in your browser.

Be the first to rate this tool

Enter the tooth counts, input speed and input torque, then press Calculate Gear Ratio.

What Is Gear Ratio Visualizer?

Gear Ratio Visualizer is a free online tool by TechnSols that works out the gear ratio of a pair of meshing gears from their tooth counts, and shows the output speed and output torque that follow from it. Type the driver and driven tooth counts, add the input speed and torque, and the tool gives the ratio, the output RPM, the ideal output torque, and a diagram of the two gears drawn from your inputs.

Advertisement

A gear pair is the simplest way to trade speed for force. A small gear driving a large gear turns the large gear more slowly, and the large gear turns with more torque. A large gear driving a small gear does the opposite, and the small gear spins faster with less torque. The ratio comes from one division: driven teeth divided by driver teeth. When the speeds on both shafts need checking, the Speed Converter changes RPM into other speed units. When the twisting force needs checking, the Torque Calculator works out torque from force and distance. When the power through the pair needs checking, the Power Converter changes watts into horsepower and back.

The diagram is what makes this tool different from a plain calculator. The two gears are drawn side by side from your inputs, so a 20 tooth driver next to a 40 tooth driven gear looks like a small gear meshing with a gear twice its size. Everything runs in your browser, and no file is uploaded anywhere. The result can be downloaded as a short text summary to keep with the design.

How To Use Gear Ratio Visualizer?

Using Gear Ratio Visualizer takes less than a minute, with no software to install and no account to make. Type the tooth counts, add the input speed and torque, press the button, and read the ratio, the output speed, the output torque, and the diagram.

Step 1: Enter The Tooth Counts

Type the teeth on the driver gear, which receives power from the motor, engine, or pedals. Then type the teeth on the driven gear, which receives power from the driver and turns the load. Both counts must be whole numbers from 1 to 1000. A 20 tooth driver and a 40 tooth driven gear give a 2 to 1 ratio, and swapping the two numbers inverts the ratio, so check which gear the power source turns before you type.

Step 2: Enter The Input Speed And Torque

Type the input speed in revolutions per minute, which is how fast the driver shaft spins. Then type the input torque in newton metres, which is the twisting force at the driver shaft. The speed must be more than 0 and 100000 RPM or less, and the torque must be from 0 to 100000 newton metres. If the torque is not known, enter 0 and read the ratio and the output speed, which do not need torque at all.

Step 3: Read The Result And Download The Summary

Press Calculate Gear Ratio and read the gear ratio, the output speed in RPM, the ideal output torque in newton metres, and the type of drive, which is reduction, overdrive, or direct drive. Download the text summary with the Download button for a record, and change any input to work out a new ratio: the old result clears at once, so a stale answer is never shown.

The whole check is one calculation, and the numbers can be used straight in a gearbox sketch or a motor sizing note.

Why Gear Ratios Matter

Gears decide how fast a machine moves and how hard it can push, and the ratio is the single number that sets both. A motor that spins at 3000 RPM is too fast for a wheel, a winch, or a conveyor, and a gear pair slows it down to a useful speed while raising the torque by the same factor. Without the right ratio, a machine is either too fast and too weak or too slow and needlessly strong. The diagram in this tool shows the two gears side by side, and the note under it states the direction change plainly, so the reversal is never a surprise in the finished machine. The Gear Ratio page explains how the ratio, the tooth counts, and the shaft speeds relate in a meshing pair.

Speed And Torque Trade Places

Speed and torque trade against each other in a fixed way. When the ratio is more than 1, the output turns slower and stronger by that factor. When the ratio is less than 1, the output turns faster and weaker by that factor. Power stays the same in the ideal case, because power is torque times speed, and one rises exactly as much as the other falls. This trade is why a bicycle has low gears for hills and high gears for flat roads, and why a crane gearbox is a large reduction. When the force at the output shaft needs checking, the Force Calculator works it out from mass and acceleration.

One Wrong Ratio Wastes The Motor

A motor works best in a narrow speed range, and the gear ratio is what keeps it there. A ratio that is too low forces the motor to run slowly under heavy load, where it draws more current and heats up. A ratio that is too high spins the load faster than it needs to go and leaves torque unused. The Ratio Calculator checks any two numbers as a ratio, which is handy when the tooth counts are not yet known.

Direction Reverses At Every Mesh

Every meshing pair reverses the direction of rotation. The driver turns one way, and the driven gear turns the other way. Two meshes bring the direction back to the original, which is why an idler gear is used when the output must turn the same way as the input.

What Can You Do With Gear Ratio Visualizer?

Gear Ratio Visualizer fits any job where two gears mesh and the speed or torque on the output shaft matters. These are the jobs it handles best, from a bicycle to a workshop machine.

Plan Bicycle Gearing

A bicycle chainring and rear cog are a gear pair, and the ratio sets how far the bike travels per pedal turn and how hard each turn feels. A 40 tooth chainring with a 20 tooth cog gives a 2 to 1 ratio, so the rear wheel turns twice for each pedal turn. A smaller cog raises the ratio and the speed, and a larger cog lowers it and eases the climb. When the load on the hub needs checking, the Bearing Calculator works out the bearing load from the shaft size and the force.

Size A Motor And Gearbox

A motor and a gearbox are chosen together, and the ratio is the link between them. Start with the load speed and the load torque, then work back through the ratio to the motor speed and the motor torque. A 2 to 1 reduction halves the speed the load sees and doubles the torque at the load, so a smaller motor can do the job. The tool shows the ideal output torque, and the real torque will be a little lower because of friction. When the machine must speed up or slow down, the Acceleration Converter changes the acceleration into the units the data sheet uses.

Check A Repair Or A Replacement Gear

When a gear is worn or broken, the replacement must have the same tooth count, or the ratio changes and the machine behaves differently. Count the teeth on the old gear and its partner, and check the ratio in the tool. If the replacement has a different count, the tool shows the new output speed and torque at once, so the change can be judged before the part is fitted.

Every gear job needs the same two answers, the ratio and what it does to speed and torque, and this tool gives both from the same four inputs.

Advertisement

Quality And Settings

Gear Ratio Visualizer keeps its settings simple, because a gear pair needs only four numbers. The inputs are checked before any calculation runs, so a bad value produces a plain message instead of a wrong answer.

  • Driver teeth: a whole number from 1 to 1000, already filled with 20.
  • Driven teeth: a whole number from 1 to 1000, already filled with 40.
  • Input speed: more than 0 and 100000 RPM or less, already filled with 1200 RPM.
  • Input torque: from 0 to 100000 newton metres, already filled with 10 newton metres.
  • Output torque is ideal: it assumes no friction and no losses.

When an input changes, the old result clears at once, and the diagram is redrawn from the new tooth counts, so the picture always matches the numbers on screen. If the numbers need changing between units, the Unit Converter changes them in seconds.

How Gear Ratio Visualizer Works

The calculator divides the driven teeth by the driver teeth to get the gear ratio, then simplifies it to whole numbers with the greatest common divisor. A 20 tooth driver and a 40 tooth driven gear give 40 divided by 20, which is 2, so the ratio is 2 to 1. The output speed is the input speed divided by the ratio, so 1200 RPM divided by 2 is 600 RPM. The output torque is the input torque multiplied by the ratio, so 10 newton metres times 2 is 20 newton metres. The Gear page describes how teeth, pitch, and meshing set these numbers in a real gear pair.

Two honest limits are worth knowing. First, the output torque is ideal, with no losses: real gears lose some torque to friction in the mesh, the bearings, and the lubricant, so the true output torque is lower than the figure shown, and the gear maker rating is the number to trust for a real build. Second, the tool covers one meshing pair only: a compound train needs each stage worked out on its own, and the stage ratios multiplied together for the total ratio.

Privacy

Everything you calculate stays in your browser. Gear Ratio Visualizer runs on your own computer, and nothing you type is uploaded to a server, stored, or shared.

Because no account is needed, there is no name, email, or history tied to what you do. Closing the tab ends the session, and the browser clears the numbers from memory.

Tips

A few habits make Gear Ratio Visualizer work smoother.

  • Count the teeth on both gears before you type.
  • Remember that swapping driver and driven inverts the ratio.
  • Read the type line: reduction means slower and stronger, overdrive means faster and weaker.
  • Treat the output torque as ideal.
  • Download the summary before you clear the numbers.

When the ratio matches the speed the load needs and the torque the motor can give, the gearing is right. If the lengths in a sketch need changing between units, the Length Converter changes millimetres into inches.

More Tools For The Same Job

These tools handle the same kinds of jobs: machines, motion, and the numbers behind them.

FAQ

Common questions about gear ratios and this tool, answered plainly.

Is Gear Ratio Visualizer By TechnSols Free?

Yes, Gear Ratio Visualizer by TechnSols is completely free to use, with no account, no sign-up, and no usage limit. You can work out as many gear pairs as you like, and everything runs in your browser, so nothing is uploaded or stored anywhere.

What Is A Gear Ratio?

A gear ratio is the driven teeth divided by the driver teeth. It says how many turns the driver makes for each turn of the driven gear. A ratio above 1 is a reduction, a ratio below 1 is an overdrive, and a ratio of 1 is direct drive.

How Do I Work Out Output RPM?

Divide the input RPM by the gear ratio. A 20 tooth driver and a 40 tooth driven gear give a ratio of 2, so 1200 RPM in gives 600 RPM out. The output speed is exact ratio arithmetic, and friction does not change it in the ideal case.

Why Is The Output Torque Ideal?

The tool assumes no losses, so the output torque is the input torque times the ratio. Real gears lose some torque to friction in the mesh, the bearings, and the lubricant. The figure shown is the ideal ceiling, and the gear maker rating is the number to use for a real build.

Can I Download My Gear Calculation?

Yes, you can download the result as a short text summary with the Download button. The summary lists the tooth counts, the input speed and torque, the ratio, the output speed, and the ideal output torque, so it works as a record for the design.

Enter the tooth counts, add the speed and torque, and read the ratio. A gear pair sized this way turns at the speed the load needs, with the torque the job needs.

Follow TechnSols on Google
Add TechnSols as a preferred source to see more of our tools in Google Search.
Add to Preferred Sources
Advertisement