What Is PCB Trace Width Calculator?
PCB Trace Width Calculator is a free online tool by TechnSols that works out how wide a copper trace on a printed circuit board must be to carry a chosen current safely. A trace that is too narrow runs hot, drops voltage and can fail, while a trace that is too wide wastes board space that a dense layout cannot spare. The calculator applies the IPC-2221 formulas to your current, layer, copper weight and allowed temperature rise, and it returns the minimum width in millimetres and mils, plus resistance, voltage drop and power lost for the length entered.
Every board designer meets the same problem. A power rail must carry two amps from a regulator to a load, or a motor driver must feed several amps to a connector. Guessing the width is risky, and copying a width from another board is worse, because the right width depends on the current, the copper weight, the layer, and how much heating the design can accept. This tool turns those four inputs into one clear number.
The calculator covers both external and internal layers, copper weights of 0.5, 1 and 2 oz, currents from 0.01 to 35 amps, and temperature rises from 1 to 100 degrees C. It also reports the cross-sectional area the formula requires, so the result can be checked by hand, and the resistance of the trace length entered, which decides the voltage drop on a long run. Everything runs in the browser, so no board data leaves the device.
How To Use PCB Trace Width Calculator
Using the tool takes four short steps. The defaults already describe a common case, two amps on an external layer with 1 oz copper and a 10 degree rise, so the first result appears as soon as the button is pressed.
Enter Your Current And Temperature Rise
Type the current the trace must carry in amps, then type the temperature rise the design can accept in degrees C. A rise of 10 degrees is the usual starting point for a general board, while 20 degrees suits a board with room to spare and 5 degrees suits a cautious design.
Choose Your Layer And Copper Weight
Pick external for a trace on an outer layer, where air can carry heat away, or internal for a trace buried between dielectric layers, where heat escapes slowly. Then pick the copper weight: 0.5 oz for fine signal work, 1 oz for general boards, or 2 oz for power work.
Read Your Results And Download Them
Press Calculate Trace Width to see the required width in millimetres and mils, the cross-sectional area, the resistance for the length entered, the voltage drop and the power lost as heat. Press Download on the result row to save the same figures as a text file. If a value is out of range, the tool names the field to fix.
The result is a minimum width from the standard, not a finished design rule. Round the width up, add margin where the board runs warm, and check the voltage drop again on long traces.
Why PCB Trace Width Matters
A copper trace is a resistor, and a resistor carrying current turns power into heat. The narrower the trace, the higher its resistance, the hotter it runs, and the more voltage it drops along its length. A trace sized by habit can pass a bench test at room temperature and still fail in a warm enclosure, after hours of use, or at peak current.
Heat Builds Up In Narrow Traces
Heat is the first reason width matters. A trace carrying two amps through a 0.3 mm width on 1 oz copper rises far more than the same current through a 0.78 mm width, and the extra heat ages the board. The IPC-2221 formula exists to keep that rise inside the chosen limit, and the Ohms Law tool shows how current, resistance and voltage relate on any circuit. Sizing by the formula keeps the temperature rise a known number.
Voltage Drop Steals Supply Margin
Voltage drop is the second reason width matters. A long, narrow trace between a regulator and a load can drop tens of millivolts, enough to push a 3.3 volt rail out of tolerance. The tool reports the drop for the length entered, so a designer can see whether a wider trace or a shorter route is needed. The Voltage Drop calculator checks the same effect for wires and cables in the wider circuit.
Board Space Costs Real Money
Board space is the third reason width matters. Every extra millimetre of trace width takes routing space from neighbouring signals, and on a dense board that space decides whether the layout fits on two layers. The calculator gives the minimum width the standard allows. The Resistor Colour Code tool helps with the other half of the same job, reading the parts that sit on those traces.
What Can You Do With PCB Trace Width Calculator?
The calculator fits board design, repair and learning. It answers the width question for power rails, motor outputs, charging paths and heater circuits, and it gives students a fast way to check a layout before ordering boards.
Size A Power Rail For A New Board
A designer laying out a new board needs the width of every power rail before routing starts. Enter the rail current, pick the layer and copper weight, and read the routing width. A 5 volt rail feeding a microcontroller might need only 0.3 mm, while a 12 volt rail feeding a motor driver needs far more, and the LED Circuit simulator shows how a small load current is worked out for the parts on the same rail. Getting the widths right before routing saves a full re-layout later.
Check A Trace On An Existing Board
A repair engineer can measure a trace on a finished board and check it against the tool. If the measured width is below the calculated width for the current the circuit draws, the trace is a likely cause of heat damage or intermittent faults. The Breadboard Circuit simulator helps test the same circuit off the board before a replacement is built. This check is quick, and it often explains a fault that looks like a bad part.
Plan A High Current Path
A high current path, such as a battery lead or a heater output, needs a wide trace, heavy copper or a copper pour instead of a trace. The tool shows how the width changes with copper weight, so the designer can compare a wide 1 oz trace with a narrower 2 oz trace. The Digital Circuit simulator covers the logic side of the same board, where currents are small and traces stay narrow. Planning the heavy paths first keeps the rest of the layout simple.
Quality And Settings
The quality of a trace width result rests on four settings. The current should be the highest steady current the trace will carry, not the average, because heating follows the peak. The layer choice matters more than most designers expect, since an internal trace needs about 2.6 times the cross-section of an external trace for the same current and rise. The copper weight must match the board order, and the temperature rise should suit the board environment. The 555 Timer simulator, the Arduino Pin simulator and the Transistor Switching simulator all model circuits whose traces deserve the same careful sizing.
- Current: use the peak steady current, including inrush that lasts long enough to heat the trace.
- Layer: external for outer layers with air cooling, internal for buried traces with slow heat escape.
- Copper weight: 0.5 oz for fine work, 1 oz for general boards, 2 oz for power paths.
- Temperature rise: 10 degrees for a general board, 5 degrees for a cautious design, 20 degrees where heat is acceptable.
- Trace length: enter the real routed length, since resistance and voltage drop grow with it.
After the calculation, compare the width with the fabricator minimum and the space the layout allows. If the width will not fit, the honest fixes are heavier copper, a shorter route, a copper pour, or splitting the current across two traces.
How PCB Trace Width Calculator Works
The tool applies the IPC-2221 curve-fit formula, which relates current, temperature rise and cross-sectional area as I equals k times the rise to the power 0.44 times the area to the power 0.725. The constant k is 0.048 for external layers and 0.024 for internal layers. The tool solves for the area, divides it by the copper thickness (1.378 mil per oz) to get the width in mils, and converts mils to millimetres at 0.0254 mm per mil. The Trace Width Guide works the same 2 amp example step by step and reaches the same 0.78 mm width.
Resistance comes from the copper resistivity of 1.68 times 10 to the power minus 8 ohm metres at 20 degrees C, applied to the trace length and area. Voltage drop is current times resistance, and power lost is current squared times resistance. The text download keeps the same figures with the formula and the date.
Privacy
The calculator runs entirely in the browser. The current, layer, copper weight, temperature rise and trace length are typed into the page and processed by JavaScript on the device, and no value is sent to a server or shared with anyone. There is no sign-in, no upload and no tracking of the numbers entered.
The text download is created in the browser from the result shown. Closing the page clears the inputs from memory, and reopening the tool starts again from the defaults. A board design can be checked on a shared computer without leaving a copy behind.
Tips
A few habits make trace width results more reliable. The formula gives a minimum, so treat it as a floor and add margin where the board runs warm or the current is uncertain. Always check the width against the fabricator rules.
- Round the width up to a value the fabricator can hold, never down.
- Use the peak current, not the average, when the load draws pulses or surges.
- Keep high current traces short, and route them before the signal traces.
- Add a copper pour or a second trace in parallel when one trace will not fit.
- Check the voltage drop on long traces, and widen the trace if it is too large.
Finally, remember that IPC-2221 is a conservative standard built from old test data, and the newer IPC-2152 guidance often allows more current for the same rise. For a high-reliability board, compare the two and measure the finished board under load. The PCB Width Calculator gives the same worked example and a quick reference table.
More Tools For The Same Job
Trace width is one part of circuit design, and these related tools cover the parts around it, from reading component values to testing the circuit before it is built.
- Ohms Law Calculator: works out voltage, current and resistance for any part of a circuit.
- Voltage Drop Calculator: checks the drop along wires, cables and long traces.
- Resistor Colour Code Calculator: reads a resistor value from its colour bands.
- LED Circuit Simulator: works out the resistor for a single LED and shows the circuit working.
- Breadboard Circuit Simulator: tests a circuit on a virtual breadboard before soldering.
- Digital Circuit Simulator: builds and tests logic circuits with gates and switches.
- 555 Timer Simulator: explores timing circuits built around the 555 timer chip.
- Capacitor code decoding: a capacitor code calculator turns a printed code such as 104 into 100 nF.
- Voltage divider design: a voltage divider designer picks resistor values for a target output voltage.
- LED resistor network design: an LED resistor network designer sizes resistors for several LEDs at once.
FAQ
These questions cover the points board designers ask most often about trace width and the IPC-2221 formula.
What Current Should I Enter For A Trace?
Enter the highest steady current the trace will carry, not the average current. Heating follows the current that flows long enough to warm the copper, so a short surge matters less than a steady load. If the load current is uncertain, enter the highest plausible value.
Why Is An Internal Trace So Much Wider?
An internal trace sits between dielectric layers with no air to carry heat away, so it runs hotter than an external trace of the same width. IPC-2221 halves the constant k for internal layers, which makes the required cross-section about 2.6 times larger. The original standard never measured internal traces directly.
How Accurate Is The IPC-2221 Formula?
The formula is a curve fit to test data from the 1950s, and it is conservative rather than exact. It does not model copper planes, board thickness, solder mask, airflow, vias or nearby heat. Treat the result as a safe starting width, add margin, and measure the finished board under load.
Does Copper Weight Change The Width Much?
Yes, copper weight changes the width directly. Doubling the copper weight from 1 oz to 2 oz halves the required width, because the same cross-sectional area is reached with half the width. That is why power boards often order 2 oz copper.
Is PCB Trace Width Calculator By TechnSols Free?
Yes, PCB Trace Width Calculator by TechnSols is free to use online with no install and no sign-up. The calculator runs in the browser, the text download costs nothing, and there is no limit on how many widths can be worked out. It is free for hobbyists, students and professional board designers alike.
Trace width is a small number with large consequences, and getting it right early keeps a board cool and reliable. Use the calculator for every power path, round the result up, and check the voltage drop.