TechnSols
Advertisement

LED Resistor Network Designer

Design LED resistor networks free online with LED Resistor Network Designer. Size series and parallel arrays, no install or sign-up needed.

Be the first to rate this tool

Enter the supply voltage, the LED forward voltage and current, then press Design Network.

What Is LED Resistor Network Designer?

LED Resistor Network Designer is a free online tool by TechnSols that sizes the resistors for many LEDs wired together in series strings and parallel arrays. Enter the supply voltage, the LED forward voltage, the LED current, the LEDs per string, and the number of parallel strings, and the tool gives the exact resistor, the nearest standard E12 resistor, the actual current, the resistor power, and the wattage rating.

Advertisement

One LED needs one resistor, but a row of LEDs needs a network, and the network must be designed as a whole. LEDs in series share one current and add their forward voltages, while strings in parallel add their currents and each string needs its own resistor. Getting that structure wrong is the commonest cause of dim LEDs, hot resistors, and dead parts. When only a single LED needs a resistor, the LED Circuit simulator calculates it for that one LED only.

This designer covers both layouts honestly: one resistor per series string, and one resistor per LED for parallel LEDs. It never offers a single shared resistor across LEDs in parallel, because parallel LEDs do not share current fairly. Every result shows the exact value, the buyable E12 value, and the real current that value gives.

How To Use LED Resistor Network Designer?

Using LED Resistor Network Designer takes less than a minute, with no software to install and no account to make. Type the supply and LED values, pick the layout, and read the network. If the resistance needs working out from voltage and current first, the Ohms Law calculator gives the value to start from.

Step 1: Enter The Supply Voltage And LED Details

Type the supply voltage in volts, the LED forward voltage Vf in volts, and the LED current in milliamps. The default is a 12 V supply, a red LED at 2.0 V, and 20 mA, which is the standard current for most indicator LEDs. Use the Vf from the LED datasheet, not a guess, because Vf changes with colour, part, and temperature. When the colour bands of a resistor on the bench need reading, the Resistor Color Code tool decodes them in seconds.

Step 2: Choose The Network Layout

Pick the layout from the menu. One resistor per series string is the efficient choice: the LEDs sit in a row, their forward voltages add, and one resistor sets the current for the whole string. One resistor per LED is the parallel choice: each LED sits across the supply with its own resistor, so every LED gets its own current control. Then set the LEDs per string and the number of parallel strings to match the array being built.

Step 3: Read The Result And Download The Summary

Press Design Network and read the exact resistor, the nearest E12 resistor, the actual current with that resistor, the resistor power, the recommended wattage rating, the number of resistors needed, and the total current drawn. Download the text summary with the Download button for a record, and change any input to work out a new network: the old result clears at once, so a stale answer is never shown.

Why Use A LED Resistor Network Designer?

LEDs are current devices, not voltage devices, and they need a resistor to set that current. Without a resistor, a small rise in voltage sends a large rise in current through the LED, and the LED burns out. A network adds a second problem: the LEDs must share the current fairly, and only the right structure does that. The Light Emitting Diode page explains how an LED holds a near fixed forward voltage once it conducts.

One Resistor Cannot Feed Parallel LEDs

Two LEDs wired in parallel across one resistor never split the current evenly. Tiny differences in forward voltage send most of the current through one LED, which heats up, drops its forward voltage further, and takes still more current until it fails. Every parallel LED needs its own resistor, and this designer builds the network that way, with one resistor per LED or one resistor per string.

Series Strings Waste Less Power

A single LED on a 12 V supply wastes most of the supply in its resistor: a 2 V LED leaves 10 V across the resistor, so five sixths of the power becomes heat. Three LEDs in series take 6 V between them and leave only 6 V across the resistor, so half the power does useful work. The designer shows the LED power share, so the efficiency of each layout is visible.

The Wrong Rating Burns Out First

A resistor that dissipates more power than its rating can take will overheat, change value, and fail, often taking the LEDs with it. The power is small in most LED work, a tenth of a watt or less, but a 1/8 W part has no margin at all on a 0.12 W job. The designer applies a two times safety rule and picks the smallest standard rating at least twice the power, so a 0.12 W resistor gets a 1/4 W part.

What Can You Do With LED Resistor Network Designer?

LED Resistor Network Designer fits any direct current job where more than one LED must light from one supply.

Light A Row Of LEDs From 12 V

Three red LEDs in series on a 12 V supply need one 300 ohm resistor at 20 mA, with 0.12 W in the resistor and a 1/4 W rating. The nearest E12 resistor is 330 ohm, which gives an actual current of 18.18 mA. When the drop across a resistor in an existing circuit needs checking, the Voltage Drop tool works that out from the current and the resistance.

Build A Parallel LED Panel Safely

A panel of LEDs for a sign or a display needs many LEDs in parallel, and each one needs its own resistor. The per LED layout sizes one resistor for a single LED and multiplies the count: ten LEDs need ten resistors, and the total current is ten times the single LED current. A seven segment display is a small panel of this kind, and the Seven Segment simulator models its segments before they are wired.

Drive Indicator LEDs From A Microcontroller Pin

Indicator LEDs on a microcontroller board usually run at 5 V or 3.3 V, with one LED and one resistor per pin, and the current must stay inside the pin limit, often 20 mA. The designer works out the resistor and the real current for the supply in use. When the pin states themselves need testing, the Arduino Pin simulator checks the logic before the LEDs are connected.

These jobs share one rule: the supply must leave headroom across the resistor, because a resistor with no voltage across it cannot set any current. If the LEDs in a string add up to the supply voltage or more, the string cannot light, and the tool refuses the design.

Quality And Settings

The quality of an LED network is decided by four choices: the layout, the forward voltage, the current, and the resistor rating.

Advertisement
  • Two honest layouts: one resistor per series string, or one resistor per LED, with no shared resistor across parallel LEDs.
  • Exact and E12 values: the exact resistor is shown next to the nearest buyable E12 value, so nothing is guessed at the shop.
  • Actual current: the current the E12 resistor really gives is shown, so brightness can be judged before the LEDs are wired.
  • Resistor power and rating: the power at both values is shown, and the rating uses a two times safety rule.
  • Whole array totals: the resistor count, the total LEDs, the total current, and the LED power share are all listed.

The settings are the six inputs: layout, supply voltage, forward voltage, LED current, LEDs per string, and parallel strings. A current of 10 to 20 mA suits most indicator LEDs, and high brightness parts may need less.

How LED Resistor Network Designer Calculates Resistor Values?

The designer starts from Ohm law applied to the resistor: the resistance equals the voltage across the resistor divided by the current. For one resistor per series string, the voltage across the resistor is the supply minus the string forward voltage, which is the number of LEDs times Vf. For 12 V, three LEDs at 2.0 V, and 20 mA, the resistor takes 6 V, and 6 divided by 0.02 A is 300 ohm. The power is 0.12 W, so the two times rule picks a 1/4 W rating. The nearest E12 value to 300 ohm is 330 ohm, and the actual current is 18.18 mA.

Two honest limits are worth knowing. First, LED forward voltage varies by part, colour, and temperature, so a Vf taken from a table instead of the datasheet can move the current by a fifth or more. Always use the datasheet Vf at the intended current. Second, the design assumes a regulated direct current supply and identical LEDs in each string. An unregulated supply, mixed LED colours in one string, or a high power LED that needs a driver and a heatsink all sit outside this tool. The LED Resistor Calculator page shows the same series and parallel array maths, and confirms the two times rating rule.

Privacy

Everything you design stays in your browser. LED Resistor Network Designer runs on your own computer, and nothing you type is uploaded to a server, stored, or shared with anyone.

Because no account is needed, there is no name, email, or history tied to what you do. Closing the tab ends the session, and your work stays yours.

Tips

A few habits make LED Resistor Network Designer work smoother.

  • Use the Vf from the LED datasheet at the current you plan to run, never a round number from memory.
  • Put as many LEDs in series as the supply allows, so less power is wasted as heat in the resistor.
  • Never share one resistor across LEDs in parallel: give every LED or string its own resistor.
  • Leave at least 2 V of headroom across the resistor, so normal Vf spread barely moves the current.
  • Download the summary before you clear the numbers, so the design stays with the parts order.

When the actual current sits close to the target, the rating has real headroom, and the total current fits the supply, the network is done. If the headroom is too small, drop one LED from each string or raise the supply voltage and design again. When the array must sit on a real board, the Breadboard Circuit simulator models the circuit first, and the finished layout can be checked against the PCB Trace calculator, which sizes the copper that carries the total current. The capacitor values in the same power supply can be decoded with the Capacitor Code calculator, which reads the printed code on the part.

More Tools For The Same Job

These tools handle the same kinds of jobs: LEDs, resistors, and circuit design.

FAQ

Common questions about LED resistor networks and arrays, answered plainly.

Is LED Resistor Network Designer By TechnSols Free?

Yes, LED Resistor Network Designer by TechnSols is completely free to use, with no account, no sign-up, and no usage limit. You can design as many LED networks as you like, and everything runs in your browser, with no hidden cost and no data leaving your computer.

Why Do LEDs In Parallel Need Separate Resistors?

Parallel LEDs never share current evenly, because tiny differences in forward voltage send most of the current through one LED. That LED heats up, takes still more current, and fails, and then the next LED takes the full current. Each LED or each string needs its own resistor.

What Happens If The Resistor Value Is Too Low?

A resistor that is too small lets too much current through the LEDs, so they run hot, dim early, and fail sooner. The actual current is shown, so a value that pushes the current above the LED rating can be spotted and swapped for the next value up.

How Many LEDs Can One String Hold?

A string can hold as many LEDs as fit below the supply voltage with headroom left across the resistor. Three 2.0 V LEDs fit on 12 V with 6 V of headroom, while six would take the full 12 V and leave nothing for the resistor.

Can I Download My LED Network Design?

Yes, you can download the result as a short text summary with the Download button. The summary lists the layout, the supply and LED values, the exact and E12 resistors, the actual current, the power, and the rating, so it works as a record for the job.

A good LED network is a fair one: every LED gets the current it was promised, every resistor runs cool, and no LED is asked to share what it cannot share. Design it from real E12 values, check the actual current, and the array will light evenly and last.

Follow TechnSols on Google
Add TechnSols as a preferred source to see more of our tools in Google Search.
Add to Preferred Sources
Advertisement