What Is RF Link Budget Calculator?
The RF Link Budget Calculator is a free online tool by TechnSols that works out whether a radio link will close before you buy hardware, climb a mast, or mount an antenna. You enter the transmitter power, the antenna gains, the frequency, the distance, the extra losses, and the receiver sensitivity, and the tool gives you the free-space path loss, the received power, and the link margin in seconds. If the margin is positive, the link should work. If it is negative, something in the design has to change.
A link budget is the running total of every gain and every loss between a transmitter and a receiver. Gains add power. Losses take it away. The transmitter puts out a certain power, the transmit antenna focuses it, the signal spreads out as it travels, cables and connectors steal a little, and the receive antenna gathers what is left. If enough power arrives, the link closes.
The tool is built for Wi-Fi installers, LoRa builders, drone pilots, radio amateurs, and students. It shows every step of the working. Nothing is uploaded and nothing is installed. Your numbers stay in your browser, and the result downloads as a plain text file.
How To Use RF Link Budget Calculator
Using the calculator takes less than a minute. Type your values into the boxes, press the Calculate Link Budget button, and read the result. The fields already hold a typical Wi-Fi example, so press the button straight away to see a full result.
Step 1 Enter Your Transmitter Values
Enter the transmit power in dBm, the transmit antenna gain in dBi, and the receive antenna gain in dBi. Most Wi-Fi access points transmit at 20 dBm, which is 100 milliwatts, and a small outdoor antenna adds around 5 dBi of gain. If your radio data sheet gives power in watts, remember that 1 watt is 30 dBm and 100 milliwatts is 20 dBm. The Ohms Law tool will convert between volts, amps, and watts if you need to check the supply side first.
Step 2 Enter Distance And Frequency
Enter the distance in kilometres and the frequency in megahertz. They decide the free-space path loss, and the loss grows by 6 dB every time either one doubles. A 5 km link at 2400 MHz loses about 114 dB in free space, while the same link at 5800 MHz loses about 122 dB. The Antenna Wavelength Calculator tool will work out the wavelength and antenna length for any frequency.
Step 3 Read The Margin And Download
Press Calculate Link Budget. The result shows the free-space path loss, the EIRP, the received power, the link margin, the maximum range, and the wavelength. A margin of 10 dB or more means the link closes with room to spare. A margin between 0 dB and 10 dB means it closes but the margin is thin. The Decibel Gain Calculator tool will turn any power or voltage ratio into decibels. Press Download on the result row to save the full budget as a text file.
Why Calculate An RF Link Budget?
Guessing a radio link is expensive. A link that fails in the field costs a second site visit and new hardware. A link budget answers the question on paper first, in seconds, for free. It shows which part of the design is weak. The standard behind the calculation is published by the ITU as ITU-R P.525, the recommendation for free-space attenuation.
Know Before You Climb
A link budget done at your desk tells you whether the planned antennas, radios, and distance can work together. If the margin is negative, you can change the plan before anyone leaves the ground. A five minute calculation saves a day of rework.
Compare Bands And Antennas
A link budget makes trade offs visible. Run the same distance at 868 MHz, 2400 MHz, and 5800 MHz and see the path loss change by more than 15 dB between the lowest and highest band. Because every figure is in decibels, each change is a simple addition or subtraction, and the best option is the one with the biggest margin.
Avoid Wasted Hardware
Buying a stronger transmitter is the most expensive way to fix a weak link, and it is often the least effective. Doubling the transmit power adds only 3 dB to the budget, while doubling the distance costs 6 dB. A better antenna or a shorter cable often buys more margin for less money. The budget shows you the cheapest fix first.
What Can You Do With RF Link Budget Calculator?
The calculator fits any point to point radio job. The three situations below are the ones people use it for most.
Plan A Long Wi-Fi Link
With 20 dBm of transmit power, 5 dBi antennas at each end, and no other losses, the received power at 2400 MHz over 5 km is about minus 84 dBm, leaving a margin of about 6 dB against minus 90 dBm sensitivity. Check the power feed with the Voltage Drop tool before you mount the radio.
Plan A LoRa Sensor Network
LoRa sensors send tiny packets over long distances, and their receivers are very sensitive, often down to minus 137 dBm. Enter the transmit power, usually 14 dBm or 20 dBm, the frequency, often 868 MHz, and the distance, and the budget shows a large positive margin even with vegetation loss added. For a custom board, the PCB Trace Width tool will work out the trace width the radio current needs.
Plan A Drone Video Link
A drone video link is a moving target, and the pilot needs to know the range at which the picture will break up. Run the budget at the planned maximum distance, and the margin tells you whether the flight plan is safe. A margin under 10 dB means the video will glitch at the far end of the flight. The LED Circuit Simulator tool will work out the resistor for a single LED on the drone.
Quality And Settings
Each input is checked before the result is shown, so impossible values give a plain message instead of a wrong answer.
- Transmit power from minus 30 dBm to 100 dBm, from a tiny sensor to a broadcast transmitter.
- Antenna gains from minus 30 dBi to 60 dBi at each end, for indoor antennas and large dishes alike.
- Frequency from 0.1 MHz to 100000 MHz, covering long wave, IoT, Wi-Fi, 5G, and millimetre wave.
- Distance from 0.001 km to 100000 km, from a room to a satellite link.
- Other losses from 0 dB to 100 dB as one lumped figure, and receiver sensitivity from minus 160 dBm to 0 dBm.
Three preset buttons fill in the frequency and distance for a Wi-Fi link at 2.4 GHz over 5 km, a LoRa link at 868 MHz over 10 km, and a 5G link at 3500 MHz over 1 km. The presets only change those two fields, so you can compare bands without retyping the whole link.
How RF Link Budget Calculator Works
The calculation follows the Friis Transmission Equation for power transfer between two antennas in free space. Free-space path loss is 20 times log10 of the distance in kilometres, plus 20 times log10 of the frequency in megahertz, plus 32.44. The effective radiated power, or EIRP, is the transmit power plus the transmit antenna gain. Received power is EIRP minus path loss, minus other losses, plus receive antenna gain. Link margin is received power minus receiver sensitivity.
Take the worked example. A 5 km link at 2400 MHz has a free-space path loss of 20 times log10 of 5, plus 20 times log10 of 2400, plus 32.44, which is 114.02 dB. With 20 dBm and 5 dBi of gain at each end, the received power is 20 plus 5 plus 5 minus 114.02, which is minus 84.02 dBm. Against minus 90 dBm sensitivity, the margin is 5.98 dB and the maximum range is about 9.95 km.
Privacy
Every calculation runs in your browser. Your values are never sent to a server, never stored, and never shared with anyone. There is no account, no sign up, and no upload. The only file that leaves your browser is the text download, and only when you press its Download button.
Because nothing is stored, closing the page clears your numbers. That is deliberate. If you need the numbers later, download the text file and keep it in your own project folder.
Tips
A few habits make the difference between a budget that predicts the real link and one that only looks good on screen.
- Aim for at least 10 dB of margin on a fixed link. A link that closes with 2 dB will drop out in rain, and a link with 6 dB has no room for a tree that grows into the path. Check the matching network resistors with the Resistor Colour Code tool, so a wrong value does not quietly eat your margin.
- Put every loss you know about into the other losses box. A 30 metre run of thin coax at 2.4 GHz can lose 3 dB or more, and four connectors can add another decibel. The Capacitor Code Calculator tool will decode the three digit code printed on any small capacitor.
- Check the far-field assumption. The Friis formula only holds when the antennas are far apart compared with the wavelength, so do not trust a budget for two antennas a few centimetres apart. Check the microcontroller pins with the Arduino Pin State simulator, because a pin set wrong can look exactly like a weak link.
- Test the link at its worst distance, not its best. A link that works in winter can fail in summer when the trees are in leaf.
- Write the budget down. Download the text file and keep it with the installation photos, so a later budget shows what changed.
The habit that matters most is the simplest one: never trust a margin you have not measured against. Use the budget to pick the design, then confirm it on site before you call the job done.
More Tools For The Same Job
These tools cover the jobs around a radio link. Each one solves a different part of the same project.
- Antenna Wavelength Calculator: works out the wavelength and antenna length for any frequency.
- Decibel Gain Calculator: turns power and voltage ratios into decibels and adds cascaded stages.
- Capacitor Code Calculator: decodes the three digit code on a capacitor into its value.
- Inductor Value Calculator: works out inductance from turns and core, and decodes inductor codes.
- PCB Trace Width Calculator: works out the trace width a current needs on a circuit board.
- Voltage Divider Designer: designs a divider that gives a target output voltage from a supply.
- LED Resistor Network Designer: designs resistor networks for several LEDs in series or parallel.
- Resistor Color Code Calculator: reads resistor colour bands and gives the value and tolerance.
- Ohms Law Calculator: converts between voltage, current, resistance, and power.
- Voltage Drop Calculator: works out the voltage lost along a cable run.
FAQ
These are the questions people ask most about link budgets.
What Is Free-Space Path Loss?
Free-space path loss is the loss a signal suffers by spreading out as it travels through empty space. It grows with distance and with frequency, by 6 dB every time either one doubles. It is the largest loss in most outdoor links.
What Link Margin Should I Aim For?
Aim for at least 10 dB on a fixed link and 20 dB or more on a mobile link or one that must work in rain. A link with a small positive margin works on a good day and fails on a bad one.
Why Does Higher Frequency Mean More Loss?
Higher frequency means a shorter wavelength, and a receive antenna of a given size captures a smaller share of the spreading wave. Moving from 868 MHz to 2400 MHz adds about 9 dB of loss, and moving to 5800 MHz adds about 17 dB.
Can I Use This Calculator For Indoor Wi-Fi?
You can use it as a rough starting point, but the answer will be optimistic indoors. Walls, floors, furniture, and people add losses the free-space model does not include, often 20 dB to 40 dB in an office. Add your best estimate of those losses into the other losses box.
Is RF Link Budget Calculator By TechnSols Free?
Yes. The RF Link Budget Calculator by TechnSols is free to use online, with no sign up, no install, and no limits on how many budgets you run. Every calculation happens in your browser, and the text download of your result is free too.
Run the budget before you build the link, and let the margin decide the design. A budget that shows a negative margin is the cheapest warning you will ever get.